free hit counter
Baroness LM180C Owner's Manual
  1. Manuals
  2. Brands
  3. Baroness Manuals
  4. Lawn Mower
  5. LM180C
  6. Owner's manual

Baroness LM180C Owner's Manual

Super mower
Hide thumbs Also See for LM180C:
Table of Contents

Advertisement

Quick Links

See also: Owner's Operation Manual
Reel Mower
Super Mower
Owner's operating manual
"Required reading" Read this manual and the owner's manual for
the engine before using the machine.
Serial No.15001
Original Instructions
Ver.1.0

Advertisement

Table of Contents
loading

Related Manuals for Baroness LM180C

Summary of Contents for Baroness LM180C

  • Page 1 Reel Mower Super Mower Owner's operating manual "Required reading" Read this manual and the owner's manual for the engine before using the machine. Serial No.15001 Original Instructions Ver.1.0...
  • Page 2 LM180C Greeting Thank you for purchasing the Baroness machine. This manual explains proper handling, adjustment, and inspection of your machine. Prior to use, carefully read this manual to thoroughly understand the contents for safe and correct operation. This machine has been shipped from the factory after comprehensive test runs and inspections.
  • Page 3 The information described in this manual is subject to change without prior notice for improvement. When replacing parts, be sure to use genuine Baroness parts or parts designated by Kyoeisha. Note that the Baroness product warranty may not apply to defects caused by the use of parts from other companies.
  • Page 4 LM180C Introduction...

  • Page 5: Table Of Contents

    LM180C Contents Safety ............... 1-1 Long-Term Storage ..........9-15 Safety management ..........1-2 For Safe Operation ..........1-2 Training ..............1-2 Before operating the machine ........ 1-2 When operating the machine ......... 1-3 Maintenance and storage ........1-4 Sound pressure level ..........2-1 Sound pressure ............
  • Page 6 LM180C Contents...

  • Page 7: Safety

    LM180C Safety Safety management ........1-2 For Safe Operation ......... 1-2 Training ............1-2 Before operating the machine ....... 1-2 When operating the machine ......1-3 Maintenance and storage ......1-4 Page 1-1...

  • Page 8: Safety Management

    LM180C Safety This machine met CEN standard EN 836: 1997 (if Never allow children or people unfamiliar with the specified label is affixed) for ride-on bunker these instructions to use or service the rakes at the time of production. machine. Local regulations may restrict the Improper use or maintenance may result in injury age of the operator.

  • Page 9: When Operating The Machine

    LM180C Safety damaged, become dirty, or peel off, please Replace faulty mufflers. replace them with new ones. Warm the engine on cold days. Set the Tighten any nuts, bolts, or screws that parking brake while warming the engine. become loose to ensure that the machine is When operating the machine always operated under safe conditions.

  • Page 10: Maintenance And Storage

    LM180C Safety Use care when approaching blind corners, Inspect the machine for damage and make shrubs, trees, or other objects that may repairs before restarting and operating the obscure your vision. equipment. When using attachments, never direct the Before removing the grass catcher/ discharge at bystanders or allow anyone near catchers.
  • Page 11 Be careful durig adjustment of the machine to machine. prevent entrapment of the fingers between moving blades and fixed parts of the machine. Consult a Baroness dealer or Kyoeisha when major repairs or assistance is required. On multi-cylinder/multi-reel machines take care as rotating one cylinder/reel can cause For safety and maximum performance, use other cylinder/reels to rotate.
  • Page 12 LM180C Safety Maintenance and storage Page 1-6...

  • Page 13: Sound Pressure Level

    LM180C Sound pressure level Sound pressure ..........2-2 Page 2-1...

  • Page 14: Sound Pressure

    LM180C Sound pressure level Sound pressure This machine was confirmed to have a continuous A-weighted sound pressure level of 93 dB (A) by measuring identical machines in accordance with the procedure specified in directive EN836:1997/EC. Sound pressure Page 2-2...

  • Page 15: Sound Power Level

    LM180C Sound power level Sound power ........... 3-2 Page 3-1...

  • Page 16: Sound Power

    LM180C Sound power level Sound power This machine was confirmed to have a sound power level of 105 dBA/lpW by measuring identical machines in accordance with the procedure specified in directive 2000/14/EC. Sound power Page 3-2...

  • Page 17: Vibration Level

    LM180C Vibration level Hand-arm vibration ........4-2 Whole body vibration ........4-2 Page 4-1...

  • Page 18: Hand-Arm Vibration

    LM180C Vibration level Hand-arm vibration This machine was confirmed to transmit a maximum vibration level of 3.63 m/s to hands and arms by measuring identical machines in accordance with the procedure specified in ISO 5349-1, 2001 5349-2, 2001. Whole body vibration This machine was confirmed to transmit a maximum vibration level of 1.12 m/s...

  • Page 19: Safety Labels And Operation Labels

    LM180C Safety labels and operation labels About the Safety labels and ... 5-2 operation labels Page 5-1...

  • Page 20: About The Safety Labels And Operation

    Part numbers for labels that need to be replaced are listed in the parts catalog. Order them from a Baroness dealer or Kyoeisha. About the Safety labels and operation labels Page 5-2...

  • Page 21: Disposal

    LM180C Disposal Waste disposal ..........6-2 About the Waste disposal ......6-2 Page 6-1...

  • Page 22: Waste Disposal

    LM180C Disposal Waste disposal About the Waste disposal Make sure that waste generated when servicing or repairing the machine is disposed of in accordance with local regulations. (e.g. waste oil, antifreeze batteries, rubber products, and wires etc.) Waste disposal Page 6-2...

  • Page 23: Product Overview

    LM180C Product Overview Specifications ..........7-2 Names of Portions .......... 7-3 Positions of the decals (Warning ... 7-3 and Instruction) Warning and Instruction Decals ....7-4 Page 7-1...

  • Page 24: Specifications

    LM180C Product Overview Specifications Model LM180C Total length 215 cm During 208 cm operation Total width Dimensions During 185 cm transport Seat 107 cm Total height Handle 102 cm Weight 387 kg Minimum turning width 230 cm Model Subaru EH30B...

  • Page 25: Names Of Portions

    LM180C Product Overview Names of Portions Positions of the decals (Warning and Instruction) quwxcl-002 6iul4h-001 Names of Portions_001 Positions of the decals (Warning and Instruction)_001 Handle Traveling clutch lever Change lever Parking brake lever Left mower unit Diff-lock pedal Reel rotation lever...

  • Page 26: Warning And Instruction Decals

    LM180C Product Overview Warning and Instruction Decals LM180C-1001Z0 Sticker, operation Warning Read the Owner's Operating Manual. Danger Danger Flying objects - Any people other than the operator must keep a safe distance from the machine. Danger Danger qigqnx-009 Rollover - Do not work on any slopes of 18 degrees or more.
  • Page 27 LM180C Product Overview R073-20057-60 Decal, engine warning Read manual. Exhaust gas is poisonous. Do not operate in an unventilated room or enclosed area. CHECK FOR LEAKAGE FROM HOSES AND FITTINGS. SHUT OFF FUEL VALVE WHEN ENGINE IS NOT IN USE.
  • Page 28 LM180C Product Overview Warning and Instruction Decals Page 7-6...

  • Page 29: Handling Instructions

    LM180C Handling Instructions Inspection Before Use ........8-2 Procedure for Cutting ........8-14 Inspection of Reel cutter (Cutting ... 8-2 cylinder) Inspection of Air Cleaner ........ 8-2 Inspection of Tires .......... 8-3 Inspection of Parking Brake ......8-3 Inspection of Brake ........8-3 Inspection of Belts ..........

  • Page 30: Inspection Before Use

    LM180C Handling Instructions Inspection Before Use Be sure to perform inspection before you start operating the machine so that you will be able to take advantage of its optimum performance for a long period of time. Inspection of Reel cutter (Cutting cylinder)

  • Page 31: Inspection Of Tires

    LM180C Handling Instructions Inspection of Engine For details on handling the engine, please refer to the separate Engine Handling Manual. Check the fuel system parts for loosened or cracked joints and leakage. Replace the parts if necessary. Blow the air to clean any grass or flammables attached inside or around the muffler.

  • Page 32: Inspection Of Transmission Oil

    LM180C Handling Instructions the engine at high loads or in high Important temperatures. Do not mix different types of engine oil. Move the machine onto a level surface, Be sure to use the engine oil that is classified stop the engine, remove the drain plug...

  • Page 33: Inspection Of Fuel Supply

    LM180C Handling Instructions Change the entire transmission oil after 50 Oil filling port hours of operation for the first time, and then Oil level plug change it every year of operation. Drain plug Move the machine onto a level surface,...
  • Page 34 LM180C Handling Instructions Fuel Supply If the fuel gauge located on the fuel tank indicates a level close to E (EMPTY), supply lead-free gasoline for automobiles at your earliest convenience. The fuel tank capacity is approximately 6.0 (6.0 liters). Inspection Before Use...

  • Page 35: Tightening Torques

    LM180C Handling Instructions Tightening torques Standard tightening torques Bolts and screws Unless otherwise instructed, tighten bolts or nuts by the specified torque using an appropriate tool. Excessive tightening of a screw may cause it to become loose or damaged. The appropriate tightening torque depends on factors such as the type of screw, its strength, and the friction of its thread and bearing surface.

  • Page 36: Principal Tightening Torques

    LM180C Handling Instructions Heat-treated screws Strength category: 8.8 Strength category: 10.9 Nominal diameter 10.9 tib3yb-002 tib3yb-003 kgf-cm lb-in kgf-cm lb-in 5 - 7 50.99 - 71.38 44.26 - 61.96 7 - 10 71.38 - 101.97 61.96 - 88.51 8 - 11 81.58 - 112.17...

  • Page 37: Adjustment Before Operating

    LM180C Handling Instructions Tightening Torque Thread locking Portion Code Part name adhesive kgf-cm lb-in Bed knife Screw, heat-treated flathead 295.71 - 256.68 - K0071000092 29 - 38 (Bottom blade) M10-20 387.49 336.34 591.43 - 513.36 - Front roller K0010100252 Bolt, heat-treated M10-25 58 - 76 774.97...

  • Page 38: Procedure To Start / Stop Engine

    LM180C Handling Instructions Sit on the seat. Adjustment of Cutting Height Make sure that you have depressed the brake pedal and pulled the parking brake Important lever. The front wheel is provided to prevent the Move the traveling clutch lever, reel rotation...

  • Page 39: Operation Of Each Section

    LM180C Handling Instructions makes the engine stop unless it meets each Move the throttle lever toward the rabbit icon of the following two conditions. (High) to increase the engine rpm, and toward the turtle icon (Low) to reduce the rpm.

  • Page 40: Lifting Lever (For Rear Mower)

    LM180C Handling Instructions Operation of Change Lever Caution Do not change the lever position during traveling. Otherwise, the transmission may be damaged. The change lever is a transmission device. It was adapted from a direct change system. To change the speed, park the machine on level...

  • Page 41: Travel Of Machine

    LM180C Handling Instructions Traveling clutch lever Reel rotation lever Operation of Reel Rotation Lever Caution Unless both left and right mower units have been lowered all the way, you are not able to operate the reel rotation lever. n9dmld-001 To rotate the reel cutter (cutting cylinder) for the...

  • Page 42: Cutting Work

    LM180C Handling Instructions Cutting Work Procedure for Cutting Before starting the engine, check the following points. An operator must be sitting on the seat. The parking brake lever must have been engaged. The change lever must be in the neutral position.

  • Page 43: Maintenance

    LM180C Maintenance Maintenance Schedule ........9-2 Maintenance Precautions ......9-3 Specified Values for Maintenance ....9-3 Main Consumable Parts ......... 9-4 Jacking up the machine ......... 9-4 About the Jacking up the machine ....9-4 Jack-up Portion ..........9-5 Lubrication ............9-6 About the Lubrication ........

  • Page 44: Maintenance Schedule

    LM180C Maintenance Maintenance Schedule Follow the maintenance schedule below. Caution Use tools appropriate for each maintenance operation. Inspect, adjust, supply, clean Replace (first time) Replace Maintenance Item Tightening the parts Fuel Air cleaner 8hrs Engine oil (first time) 50hrs Engine oil filter...

  • Page 45: Maintenance Precautions

    First, learn well the maintenance operations you plan to perform. For the safe and best performance of your machine, use Baroness genuine parts for replacement and accessories. Please note that our product warranty may be void if you use non-genuine parts for replacement or accessories.

  • Page 46: Jacking Up The Machine

    LM180C Maintenance Clearance between pedal stopper and Brake pedal 5 - 7 mm brake pedal Clearance between rod-tension metal Traveling clutch 5 mm fitting and collar Clearance between rod-tension metal Reel rotation lever 5 mm fitting and collar Left and right...

  • Page 47: Maintenance (Mower)

    LM180C Maintenance Front axle, right Jack-up Portion rwyt62-013 Jack-up Portion_003 Front axle, left rwyt62-014 rwyt62-011 Jack-up Portion_004 Transmission case, lower Jack-up Portion_001 Jack-up Portion Front axle, center Front axle, right Front axle, left Transmission case, lower Transmission axle case, left...

  • Page 48: Lubrication

    LM180C Maintenance Transmission axle case, right No. of Portion Greasing Points Front wheels Front wheel front pin Reel housing Mower frame Mower lifting arm Diff-lock pedal Handle tension rwyt62-017 Brake pedal Jack-up Portion_007 Rear mower oscillating metal part Lubrication Rear roller...

  • Page 49: Maintenance (Mower)

    LM180C Maintenance Reel housing Diff-lock pedal There is one point each on the left and the right of each unit. 8bq62b-061 Greasing Point_007 8bq62b-058 Handle tension Supply automobile transmission gear oil #90 Greasing Point_004 Mower frame every 50 hours of operation.

  • Page 50: Lapping Of Reel Cutter

    Do not perform lapping with any other Greasing Point_012 persons. Mower tension Have the following items ready: Lapping machine [Baroness RM20B], Strips of newspaper, Abrasive [Lapping powder mixed with abrasive; or gel compound (Baroness genuine abrasive)], Brush, 27 socket wrench. 8bq62b-067 27 mm Greasing Point_013 zhz6po-001...

  • Page 51: Maintenance (Main Body)

    Apply the abrasive evenly with the brush on Refer to the Tightening Torque table. the top side of reel cutter (cutting cylinder) Note that the Baroness product warranty may where the newspaper was cut well or of not apply to defects caused by incorrect or chalk-marked locations.

  • Page 52: Adjustment Of Belt Tension

    Caution engaged. Refer to the Tightening Torque table. Tighten the adjusting bolt and make sure Note that the Baroness product warranty may that the collar is fixed securely. not apply to defects caused by incorrect or overtorque tightening. 5 mm...
  • Page 53 LM180C Maintenance Adjust the clearance between the rod- tension metal fitting and the collar to be 1 mm 5mm, when the traveling clutch lever is engaged. Tighten the adjusting bolt and make sure that the collar is fixed securely. l36w96-003...

  • Page 54: Adjustment Of Parking Brake

    LM180C Maintenance Tighten adjusting nut A and make sure that the rod is fixed securely. Raise the rear mower unit, then make sure that the reel cutter (cutting cylinder) will not rotate when the machine travels. 10 mm l36w96-006 1 mm...

  • Page 55: Adjustment Of Brake

    LM180C Maintenance is larger than 7mm, the brake may be damaged.) Affix the brake pedal to the front of the brake rod securely using the pin. Tighten the lock nut to secure the front of the brake rod firmly. Make sure that the brake is not applied any longer when you release the brake pedal.

  • Page 56: Adjustment Of Mower Stopper

    LM180C Maintenance Adjust the wire so that the diff-lock wire and the diff-lock lever show a little play when the lever returns to its resting position under spring tension. Tighten the nut and fix the wire adjustment bracket completely. gawfw2-001...

  • Page 57: Right Mower

    LM180C Maintenance Wire adjustment metal fitting Wire (to hook the mower) Right mower unit Hook metal fitting Bottom of the hook Adjustment of Wire to hook the rear mower 569gs3-002 Loosen the nuts and move the wire Adjustment of Wire to hook the rear mower_002...
  • Page 58 LM180C Maintenance Long-Term Storage Page 9-16...
  • Page 61 1-26, Miyuki-cho, Toyokawa, Tel : (0533)84-1390 Head Office Aichi-Pref. 442-8530 Japan. Fax : (0533)89-3623 LM180C--UM--GBZ/11D-00-S.K...

Table of Contents