Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Tannoy Revolution XT
Summary of Contents for Tannoy Revolution XT
- Page 1 O WNE R’ S MA N U A L...
-
Page 2: Table Of Contents
If you suspect a problem with a Tannoy product, in the first instance, discuss it with your Tannoy dealer. If you require further assistance then we ask that you deal directly with your local Tannoy distributor. If you cannot locate your distributor please contact Tannoy Customer Services, at the address given below. -
Page 3: Introduction
24 hrs use. Once they have been further run-in over a longer period, there will be clear enhancement of the stereo imaging, mid-band quality and bass performance characteristics. We are confident that you will continue to enjoy your new Tannoy Revolution XT loudspeakers for many years to come. -
Page 4: Amplifier Choice
Positioning and fine-tuning. The Revolution XT Mini may also be wall mounted with a suitable bracket, using two inserts on the rear of the loudspeaker, with standard 60mm spacing. The thread in the inserts is M5. It is the responsibility of the customer to ensure the chosen bracket is used within its load rating, and the bracket is securely mounted to the wall with suitable hardware. -
Page 5: Installation
• Switch the amplifier on with the volume control set at its lowest setting. Select a favourite source and slowly turn up the volume to a low level. Check that bass and treble information is being reproduced from both speakers - if not, switch OFF the amplifier and recheck the connections. REVOLUTION XT MANUAL_05... -
Page 6: Bi-Amping
(See Fig. 4) POSITIONING AND FINE TUNING To get best results from your new Tannoy Revolution XT loudspeakers it is worthwhile spending a little time finding the optimum setup configuration. Begin by angling the speakers towards your chosen listening position, usually this is on the centre line of the room, so that when seated you can just see the inner side panel of each speaker. -
Page 7: Revolution Xt Home Theatre 5.1
As with the main speakers the front baffle panel should be as near as possible in line with the screen surface. The Revolution XT C can be wired in single wire, bi-wire or bi-amp modes. Please refer to figs. 2, 3 & 4 for connection guidance bearing in mind that connection should be made to the dedicated centre channel output on your A/V processor amplifier/s. -
Page 8: Technical Specifications
(39.6 x 10.6 x 12.5”) (42.5 x 12.5 x 13.6”) Net weight 7.5 kg (16.4 lbs) 16.3 kg (35.9 lbs) 19.9 kg (43.9 lbs) Finish Dark Walnut Dark Walnut Dark Walnut Medium Oak Medium Oak Medium Oak 08_ REVOLUTION XT MANUAL... -
Page 9: Technical Specifications
TECHNICAL SPECIFICATIONS REVOLUTION XT Mini REVOLUTION XT C PERFORMANCE Recommended amplifier power 25 - 100 25 - 120 (watt RMS) Continuous power handling (watt RMS) Peak power handling (watt) Sensitivity (2.83 volt @ 1 m) 88 dB 89 dB Nominal Impedance (ohm) -
Page 10: Set-Up Diagrams
SET-UP DIAGRAMS Fig.1 Unpacking Fig.2 Single Wire Mode TO RIGHT SPEAKER POWER AMPLIFIER LINKS IN PLACE LINKS REMOVED 010_ REVOLUTION XT MANUAL... - Page 11 SET-UP DIAGRAMS Fig.3 Bi-Wire Mode TO RIGHT SPEAKER POWER AMPLIFIER LINKS REMOVED LINKS REMOVED Fig.4 Bi-Amp Mode TO RIGHT SPEAKER HIGH FREQUENCY POWER AMPLIFIER LOW FREQUENCY POWER AMPLIFIER TO RIGHT SPEAKER LINKS REMOVED REVOLUTION XT MANUAL_011...
-
Page 12: Set-Up Diagrams
SET-UP DIAGRAMS Fig.5 Recommended Positioning - Stereo Pair 0.5 METRES OR MORE 1.5 To 4.5 METRES ONE METRE OR MORE Fig.6 Recommended Positioning - Home Cinema REAR REAR 012_ REVOLUTION XT MANUAL... - Page 13 NOTES REVOLUTION XT MANUAL_013...
- Page 14 014_ REVOLUTION XT MANUAL...
- Page 15 REVOLUTION XT MANUAL_015...
- Page 16 Tannoy Limited - product designed in the United Kingdom. Tannoy adopts a policy of continuous improvement and product specification is subject to change. All other trademarks remain the property of their respective owners. tannoy.com...