Important Safety Information Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. This apparatus shall not be exposed to dripping or splashing liquid and no object filled with liquid, such as a vase, should be placed on the apparatus. Clean only with a dry cloth.
Page 4
Important Safety Information AVIS RISQUE DE CHOC ÉLECTRONIQUE - NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage”...
Introduction The Samson MXS2800 is a stereo power amplifier boasting an abundance of power in a lightweight single rack-space design. It has been designed to provide solid, clean output with low distortion and wide dynamic range, along with the dependability demanded by professional front-of-house engineers and installers.
Features • Lightweight, high-power, single rack-space Class D power amplifier. • 2 x 1700 Watts at 2Ω, 2 x 850 Watts at 4Ω 3400 Watts at 4Ω, 1700 Watts at 8Ω bridged mono • Clean, crisp sound, 0.02% THD, dynamic range of 100 dB, and frequency response of 20 Hz to 20 kHz, guarantee ultra-clean sound quality •...
Getting Started with the MXS2800 Setting up your MXS2800 amplifier is a simple procedure which takes only a few minutes: Remove all packing materials (save them in case your units needs future service) and decide where the amplifier is to be physically placed—it can be used free-standing or mounted in a standard 19”...
Front Callouts POWER Switch - Use this push button switch to power the MXS2800 amplifier on or Channel Level Controls - Two detent controls to precisely adjust the output level of each channel. PEAK - The PEAK indicator lights whenever the channel is outputting signal at full strength.
Rear Callouts Input Connectors - Connect incoming signal to these electronically balanced XLR or unbalanced RCA jacks. MODE Switch - For normal operation, place this three-way switch in the STEREO posi- tion. When placed in its BRIDGE position, the signal arriving at the Ch A input only is again routed to both power amplifiers (the Ch B input is ignored), but the two power amplifiers are bridged together.
Bridge Mode The MXS2800 power amplifier provides a rear-panel switch that allows it to be used in either a Stereo or Bridge mode. When this switch is placed in the STEREO position, the MXS2800 functions as a true stereo amplifier, where both of the two independent amplifier channels (Ch A and Ch B) can receive different input signals and produce independent output signals.
System Setup Examples Typical amplifier and speaker configurations for the MXS2800: Stereo Input: Stereo Full Range Speakers Mono Input: Bridge Mono Output...
Specifications 8 ohms 450W Rated Output Power Stereo both channel 4 ohms 850W driven 2 ohms 1700W 8 ohms 1700W Rated Output Power Bridged mono 4 ohms 3400W Signal to Noise Ratio (20Hz-20k) >100dB Distortion (SMPTE-IM) 0.02% Input sensitivity @ 8ohms Voltage Gain 0dBu Voltage Gain @ 8ohms 35dB...
Wiring Guide RCA Connector Tip (signal) Tip (signal) Tip (signal) Sleeve (ground) Sleeve (ground) Sleeve (ground) XLR Balanced Connector Common (1) +Hot +Hot (2) (ground) Common (ground) Solder Points End View Female XLR -Cold -Cold (3) Common (1) Tip (signal) Hot (2) Common (1) +Hot (2)
Page 16
Samson Technologies Corp. 45 Gilpin Avenue Hauppauge, New York 11788-8816 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 631-784-2201 www.samsontech.com...