Advertisement
Quick Links
Installation and User Guide
C
V
I
E
W
™
H
D
H
A
C
V
I
E
W
™
H
D
H
A
E
I
L
I
N
G
I
D
E
W
A
Y
E
I
L
I
N
G
I
D
E
W
A
Y
Ceiling Mounted Motorized Camera Lift System for the Vaddio™
ClearVIEW™ Family of HD PTZ Cameras
©2011 Vaddio - All Rights Reserved
●
●
CeilingVIEW HD HideAway
Document Number 342-0289 Rev. B
Advertisement
Related Manuals for VADDIO CEILINGVIEW HD HIDEAWAY
Summary of Contents for VADDIO CEILINGVIEW HD HIDEAWAY
- Page 1 Installation and User Guide ™ ™ Ceiling Mounted Motorized Camera Lift System for the Vaddio™ ClearVIEW™ Family of HD PTZ Cameras ©2011 Vaddio - All Rights Reserved ● ● CeilingVIEW HD HideAway Document Number 342-0289 Rev. B...
- Page 2 CeilingVIEW HD HideAway Manual Inside Front Cover - Blank CeilingVIEW HD HideAway Manual, Document Number 342-0289 Rev. B Page 2 of 24...
- Page 3 The Vaddio CeilingVIEW HD HideAway is a ceiling mounted motorized camera lift system that provides the ability to quietly lower a Vaddio ClearVIEW HD PTZ camera from the ceiling, retract it back into the ceiling and completely hide the camera. The CeilingVIEW HD HideAway enclosure presents a more aesthetically pleasing solution for camera mounting when compared to exposed wall ceiling mounts.
- Page 4 Installation and User Guide (342-0289) Figure 2: System Configuration with CeilingVIEW HD HideAway motorized camera lift, CeilingVIEW HD HideAway Power Interface, HD- 18AW PTZ Camera, Quick-Connect DVI/HDMI SR, ProductionVIEW HD MV with TeleTouch Touch Screen 22” Monitor and Projector.
- Page 5 Remove the nine (9) Phillips screws from the Front Access Panel and remove the panel. Note: There is a safety interlock switch on the upper left side of the CeilingVIEW HD HideAway Back Box Assembly that will not allow operation of the CeilingVIEW HD HideAway with the Front Access Panel removed.
- Page 6 ***IR OUT OFF: This dip switch is UP when using the Vaddio IR Remote Commander. This switch should be down if IR Forwarding is used or if the Vaddio IR Remote Commander will not be used. Note: If the dip switch is set to DN it will disable the IR receiver in the Vaddio Camera.
- Page 7 Figure 8: Incorrect placement of Ceiling Tile Brace Note: The CeilingVIEW HD HideAway Motorized Back Box Assembly can also be mounted in the Ceiling Tile Brace with the camera facing any one of four positions: Figure 9: CeilingVIEW HD HideAway Motorized Back Box...
- Page 8 Provide and install four (4) individual support cables for connection to the Ceiling Tile Brace (see Figure 12) Attach each of the support cables for the CeilingVIEW HD HideAway System to the appropriate building structure support. Note: The photo examples (see Figures 12 and 13) show the use of cable clamps to secure the cable to the ceiling structure and the turnbuckles.
- Page 9 M. Check and verify that each of the four (4) individual support cables are all equal in tension and that the weight of the CeilingVIEW HD HideAway is supported mainly by the cables and not by the suspended ceiling tile. This can be verified by looking carefully at the ceiling tile below the ceiling and checking for signs of curving or bowing of the ceiling tile (compare to other suspended ceiling tiles near your installation area).
- Page 10 (4) conductor Phoenix Connector to the IR Sensor Circuit Board and carefully feed the excess cable back into the CeilingVIEW HD HideAway Motorized Back Box Assembly. II. Align and attach the Ceiling Trim Ring Assembly to the CeilingVIEW HD HideAway Motorized Back Box Assembly with five (5) white countersunk screws.
- Page 11 Printed Circuit Board (PCBA). This connector is used to provide PTZ control of the Vaddio ClearVIEW HD PTZ Camera that is installed for use in the CeilingVIEW HD HideAway motorized camera lift system from external devices. PTZ camera control can be provided by various Vaddio ProductionVIEW Control Consoles or a ProductionVIEW Precision Camera Controller (see Figure 27 for a list).
- Page 12 HideAway Motorized Back Box Assembly. The excess cable may become damaged or caught in the lift mechanism! D. Re-install the Front Access Panel with the nine (9) Phillips screws on the CeilingVIEW HD HideAway back box. Note: There is a safety interlock switch on the upper left side of the CeilingVIEW HD HideAway Motorized Back Box Assembly that will not allow operation of the CeilingVIEW HD HideAway with the Front Access Panel removed.
- Page 13 (PCBA) will turn on. The Yellow LED will turn off when the Lift Calibration is de-activated 6) Lift Power Blue LED: A Blue LED will be on when Lift Power/Lift Trigger from the CeilingVIEW HD HideAway Power Interface is detected in the Main Printed Circuit Board (PCBA).
- Page 14 Overview: The Vaddio IR Remote Commander, included with all Vaddio ClearVIEW HD PTZ Cameras and packages, provides for simple IR remote control of the CeilingVIEW HD HideAway and the Vaddio ClearVIEW HD PTZ Camera functions. The IR Remote Commander is also used to calibrate and set the upper and lower lift stops on the Camera Lift Bracket ensuring the platform bracket stops in precise alignment with the Trim Ring Assembly.
- Page 15 Instructions for Calibrating; Setting the Upper and Lower Lift Stops: Place the CeilingVIEW HD HideAway into the Calibration Mode: With the Blue Power LED on steady in the CeilingVIEW HD HideAway Trim Ring Assembly, press and hold the Calibration push button on the IR Circuit Board in the Trim Ring Assembly until Blue Power light is flashing.
- Page 16 Trim Ring Vaddio IR Remote Commander: Setting the Upper and Lower Lift Stops Note: The CeilingVIEW HD HideAway must be in the Calibration mode in order to set the Upper and Lower Lift Stops. Back Light...
- Page 17 Automated Content Presentation Systems and the Vaddio ClearVIEW HD PTZ Cameras. A. The CeilingVIEW HD HideAway has been programmed to power on and off when it receives the power on or off command via RS-232 from the Vaddio Camera Control Consoles and Automated Content Presentation Systems.
- Page 18 Lift Contact pair. As the Vaddio HD PTZ Camera is lowered by latching the Lift Contact, it will power up and go to its home position. Once the lift has stopped, the Vaddio HD PTZ Camera will receive PTZ commands from the Polycom IR Remote or the Vaddio IR Remote Commander.
- Page 19 Example 2: Cisco TelePresence System (TANDBERG) Codec with IR Receiver: A. To add the Vaddio HD PTZ Camera video image and IR control of the Vaddio HD PTZ Camera, it will be necessary to connect a Vaddio RJ-45 to DB9 Adapter (PN 998-1002-232) to a COM port on the Cisco TelePresence (TANDBERG) Codec.
- Page 20 HideAway on and lower the camera lift (see Figure 26). The Vaddio IR Remote Commander must be pointed to the CeilingVIEW HD HideAway (in the direction of the IR Sensor in the Trim Plate Assembly (see Figure 23) to activate the CeilingVIEW HD HideAway and lower the camera lift. Once the camera lift is lowered, the Vaddio IR Remote Commander must be pointed to the front of the Vaddio HD PTZ Camera in order to be received by the camera to control PTZ functions.
- Page 21 Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the user’s authority to operate this equipment.
-
Page 22: Warranty Information
Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under warranty and is found to be defective. If the product is out of warranty, Vaddio will test then repair the product or products. The cost of parts and labor charge will be estimated by a technician and confirmed by the customer prior to repair. - Page 23 CeilingVIEW HD HideAway Manual Inside Rear Cover - Blank CeilingVIEW HD HideAway Manual, Document Number 342-0289 Rev. B Page 23 of 24...
- Page 24 Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com ©2011 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, CeilingVIEW, Quick-Connect, ProductionVIEW, ClearVIEW, EZCamera, AutoPresenter, HSDS and PowerRite are registered trademarks of Vaddio.