Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for ACT 6000
- Page 1 ACT 6000 Digital Multimeter User`s Manual www.actmeters.co.uk www.actmeters.com...
- Page 2 & Safety Executive (HSE) Guidance Note GS38 before using this or any other test equipment on live mains. For your own safety it is essential to use adequately fused test leads, such as the ACT/418F, when working on an unfused incoming mains supply (eg. Consumer Unit / Tails).
-
Page 3: International Electrical Symbols
WARNING To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. To avoid electrical shock hazard, observe the proper safety precautions when working with voltages above 60 VDC or 30 VAC rms. These voltage levels pose a potential shock hazard to the user. -
Page 4: Product Description
2) PRODUCT DESCRIPTION 1) 3-5/6 digits 6000 count LCD display 2) Push-buttons for special functions & features 3) Selector to turn the Power On or Off and Select a function 4) Input Jack for milli-amp and micro- amp current functions 5) Input Jack for all functions EXCEPT current (A, mA, A) -
Page 5: Operation
*Number of Bar-graph pointer is used to indicate input range (sensitivity) selected. 1/2/3/4 pointers indicate 6/60/600/1000V, 6/10/-/-A, 60/600/-/-mA or 600/6000/-/-uA is selected in corresponding V, A, mA or uA function respectively. ( “-” means range not available) *The Hz of mV function is designed specially for logic level (3V or 5V family) - Page 6 Resistance, Continuity & Diode test functions Press the SELECT button momentarily to select the subject functions in sequence. Last selection will be saved as power up default for repeat measurement convenience. CAUTION Using resistance or continuity functions on a live circuit will produce false results and may damage the instrument.
- Page 7 DCmV & ACmV Press the SELECT button to select the subject functions in sequence. Last selection will be saved as power up default for repeat measurement convenience. A, mA, and A Current functions Press SELECT button to toggle between DC and AC. Last selection will be saved as power up default for repeat measurement convenience.
- Page 8 The instrument is equiped with an optically isolated interface port on the rear for data communication. Hold down the HOLD button while turning the meter on to enable the PC-COMM output. The optional PC interface kit ACT/6000IK is required to connect the meter to your PC`s RS232 or USB ports.
- Page 9 Backlit LCD display Hold down the SELECT button for 1 second or more to toggle the LCD backlight. The backlight will be turned off automatically after 32 seconds to extend battery life. Hold Press HOLD to hold the present value on the display. Press again to exit this mode.
-
Page 10: Maintenance Warning
Most measuring functions through this terminal will then be open circuit. The series fusible resistors and the spark gaps should only be replaced by ACT Meters Ltd. Refer to the LIMITED WARRANTY section for obtaining warranty or repair service, or call +44 (0) 1744 88 6660. -
Page 11: General Specification
Special Features: Backlit LCD; Auto-ranging; Relative Zero mode; Display Hold; EF-Detection (NCV); Interface capabilities with PC computer; Input warning detection Included Accessories: Gold-plated (tips) silicon test lead set; Rubber Holster; Magnetic Hanger; 2 x AAA batteries (installed); user’s manual Optional Accessories: ACT/6000IK PC Interface Kit, ACT/430N Padded Case,... -
Page 12: Electrical Specification
ACT/CA60 Current Clamp 6) ELECTRICAL SPECIFICATION Accuracy is given as +/- (% of reading digits + number of digits) or otherwise specified @ 23 C +/- 5 C and less than 75% R.H. AC Voltage Open Circuit Voltage: < 1.8VDC... - Page 13 Red (+) test probe for direct contact measurement All specifications are nominal and may change as design improvements occur. ACT Meters Ltd shall not be liable for damages resulting from misapplication or misuse of its products. E&OE.
-
Page 14: Limited Warranty
ACT Meters Ltd assumes no risk for damage in transit. ACT Meters Ltd will, at its option, repair or replace the defective product free of charge. However, if ACT Meters Ltd determines... - Page 15 Heath & Safety Executive (HSE) Guidance Note GS38 before using this or any other test equipment on live mains. For your own safety it is essential to use adequately fused test leads, such as the ACT/418F, when working on an unfused incoming mains supply (for example Consumer Unit / Tails).
- Page 16 A C T METERS LTD OLD SMITHY, CHURCH RD, RAINFORD, MERSEYSIDE WA11 8HD UNITED KINGDOM Tel: +44 (0) 1744 88 6660 Fax: +44 (0) 1744 88 6661 Email: sales@actmeters.com www.actmeters.co.uk www.actmeters.com...