Related Manuals for Zennio ZVI-TMDP4
Summary of Contents for Zennio ZVI-TMDP4
- Page 1 KNX Capacitive Touch Switch (4/6/8 Main Buttons + 5 Additional Buttons) ZVI-TMDP4 ZVI-TMDP6 ZVI-TMDP8 Application Program Version: [1.2] User Manual Version: [1.2]_a www.zennio.com...
-
Page 2: Table Of Contents
2.2.2.4 Individual Buttons ................... 36 2.3 LED illumination......................38 2.3.1 Illumination Modes ....................38 2.3.2 Brightness Levels ....................41 2.4 Welcome Back Object ....................44 2.5 Locking the Touch Panel ....................46 2.6 Sounds ..........................47 http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... - Page 3 Touch-MyDesign Plus 2.7 Inputs ..........................50 2.8 Thermostat ........................51 2.9 Internal Temperature Sensor ..................52 ANNEX I: Communication Objects ....................53 http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
-
Page 4: Document Updates
Extension of the functionality of the 1-button dimming 25, 33 control. Extension of the functionality of the 1-button shutter control. 26, 34 Update of the communication object table. 57-66 Changes in the application program: [1.1]_a • Internal optimisation of the ETS project. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... -
Page 5: Introduction
1.1 TOUCH-MYDESIGN PLUS Touch-MyDesign Plus is an updated version of the original Touch-MyDesign, the KNX multifunction capacitive touch switch from Zennio. Like the classic model, Touch- MyDesign Plus provides a fully customisable solution for the room control, including hotel rooms, offices or any other environment where the user needs to control climate systems, lighting, blinds, scenes, etc. -
Page 6: Installation
To install the device, it is first necessary to mount the metallic plate into a square/round standard appliance box through the suitable screws. Next, Touch-MyDesign Plus is connected to the KNX bus through the corresponding terminal on the rear side of the http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... - Page 7 For detailed information about the technical features of Touch-MyDesign Plus and for safety instructions for the installation process, please refer to the Datasheet bundled with the original packaging of the device and also available at www.zennio.com. http://www.zennio.com Technical Support:...
-
Page 8: Configuration
In the particular case of an external temperature probe (such as model ZN1AC-NTC68 from Zennio), it will be possible to use it with independence of the built- in temperature sensor of the device, which implements its own communication objects and can be enabled and disabled in parameters. - Page 9 “Vertical”) of the device, with the aim of implementing a logical behaviour in the two-button controls. Figure 5 Device Orientation Note: the particular behaviour of the two-button controls (which one does what) is defined through Button Pair Action, as explained below. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 10 Down: 0 / Off / Decrease / Down Up: 1 / On / Increase / Up Horizontally-oriented Down: 1 / On / Increase / Up device Up: 0 / Off / Decrease / Down Every Button Pair is Configured Separately http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 11 (e.g., when the user touches a button that has been configured to send scene commands; see section 2.2). [Z] Temperature Setpoint: object for sending temperature values when the user touches the additional push buttons, which by default are assigned the “Temperature Setpoint” function (see section 2.2). http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
-
Page 12: Touch Buttons
The additional buttons, aligned and separated from the main buttons. All the main buttons are identical, and also every additional button is identical to the others, which brings a high level of versatility for a wide variety of applications. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... -
Page 13: Main Buttons
ETS by default. While all the main buttons remain disabled, it will only contain a sub-tab named Configuration. Figure 8 Main Buttons - Configuration. One drop-down list is shown per pair of main buttons. The options under it are: http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... -
Page 14: Disabled
“on” state, and off while in the “off” state. Dimmer: short-pressing one of the two buttons will make Touch-MyDesign Plus send a switch-on order to the bus, while doing so on the other button will make http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... - Page 15 (i.e., they will work as a joint control; for independent buttons, please configure them as individual). Different objects will be used for the short and long presses. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 16 Please note that in the next pages the general notation “[X]” is used for the name of the communication objects, as “X” depends on the button pair (A, B, etc.). Switch Figure 10 Pair Buttons – Switch. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 17 As explained in 2.2.1.2, the alternation of the on/off and step requests will be conditioned to these statuses, to prevent sending ineffective requests. The parameters for this function are: http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 18 The move orders will be sent through “[X] Move Shutter”, while the stop orders will be sent through “[X] Stop Shutter / Step” (for Standard type) or “[X] Stop Shutter” (for Hold & Release type). The parameters for this function are: http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 19 “Left: 1; Right: 0” (or “Down: 1; Up: 0” under a horizontally-oriented configuration. Note: this parameter will remain hidden unless having selected “Every button pair is configured separately” in Button Pair Action (see section 2.1). http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
-
Page 20: Individual
Binary: whenever the user touches the button, a binary value will be sent to the KNX bus. This value is configurable and may be 0 or 1, or alternate with every touch according to the sequence 1 0 1 … http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... - Page 21 The available ranges are shown next. 1-byte 2-byte Unsigned 0 – 255. 0 – 65535 Signed -128 – 127. -32768 – 32768. The “state-dependent” LED illumination mode is analogous as for the Scaling Constant function. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 22 Note that the device considers that the current light level is the value of a specific objected provided to be written from the KNX bus (i.e., to receive feedback from the dimmer). The light dimmer is therefore responsible of keeping its value up to date. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 23 Down: a short press will always send a step-down / stop order, while a long press will always send a move down order. • Toggle: choosing this option, the direction of the motion will alternate (upwards / downwards) for both the move and the step http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 24 Releasing the button will always send a stop order. • Toggle: the direction of this motion (upwards or downwards) will alternate with every touch, according to the following sequence: downwards upwards downwards … However, there are some exceptions to this alternation: http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 25 Constant”, “Counter Constant”, “Float Constant”, “Dimmer” and “Shutter”. Depending on the function, some more parameters are involved (as described next). Please note that in the next pages “[Xn]” is used as a general notation for the http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 26 Action: sets the value to be sent to the bus (through objects “[Xn] Binary Control: B“ (where “B” depends on the action selected) when the user touches the button. The options are “Send 0”, “Send 1” and “Toggle 0/1”. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 27 “Send 0” (default) and “Send 1” LED Illumination Control: analogous to the homonymous parameter for the “Disabled” and “Binary” functions (see above). The options in this case are “Regular” and “Dedicated Object”. Two Objects (Short Press / Long Press) http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 28 “LED Illumination State Object”, to make the state of the LED correspond either to object “[X] Two Objects: Short Press” (“Short Press Object”) or to object “[X] Two Objects: Long Press” (“Long Press Object”). Scene http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 29 Figure 21 Individual Button - Scaling Constant. Object Value: sets the value to be sent to the KNX bus when the user touches the button. The available range and the object through which the value is sent depends for each case: http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 30 “[Xn] Light Dimming (Decrease)” four-bit objects (also depending on the selected action). The “[Xn] Light Dimming (Status)” one-byte object should be linked to the light level status object of the dimmer. As explained in 2.2.1.3, the alternation of the on/off and http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 31 Direction)”, “[Xn] Move Shutter Up” or “[Xn] Move Shutter Down” one-bit objects (depending on the selected action: “Toggle”, “Up” or “Down”, respectively), while the step up/down orders will be through the “[Xn] Stop Shutter / Step”, “[Xn] Stop http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 32 Action: defines the order type that the button will send once a short or long press is performed (“Toggle”, “Up” or “Down”). LED Illumination Control: analogous to the homonymous parameter for all the previous functions (see previous pages). The options in this case are “Regular” and “Dedicated Object”. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
-
Page 33: Additional Buttons
ETS by default. This tab comprises another one named “Configuration”, containing one parameter: Function: sets the desired function for the additional buttons. The options are “Temperature Setpoint” (default selection), “1-Byte Control (Unsigned Int)”, “1- http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... -
Page 34: Temperature Setpoint
(“Temperature Setpoint”) will be available under “Additional Buttons” in the tree on the left. Figure 25 Additional Buttons - Temperature Setpoint. This window contains five textboxes (“Button n: Value”) to enter the particular setpoint http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... -
Page 35: 1-Byte Control (Unsigned Integer)
LED of such button will turn on (and the others off). Note: the INFO textboxes are functionless (they simply bring the option to add a description to each button of the project) and can be hidden if desired. See section 2.1. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... -
Page 36: 1-Byte Control (Scaling)
(except for “Dimmer” and “Shutter”, which won’t allow individual action selection and will always perform a “Toggle” behaviour) working as such: http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... - Page 37 “[Zn]” (with “n” being the number of the button: 1, 2, 3, 4 or 5) and not with “[Xn]” (with “X” depending on the button pair: A, B, etc.). http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
-
Page 38: Led Illumination
“0” will make one of the LEDs light (leaving the other one off), while the value “1” will make them switch their states. Table 1 illustrates which of the above are configurable for each function. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... - Page 39 (see section 2.1), it is also possible to define a general behaviour for all of them, thus not being then necessary to configure the same option multiple times. In case of opting for a general configuration, the options are: http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 40 (section 2.2). In case of desiring a similar behaviour for all of the LEDs, please find the parameter “LED Illumination Control (All Buttons)” in the General configuration screen. This parameter is explained in section 2.1. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
-
Page 41: Brightness Levels
A general parameter is provided to make the ETS parameterisation easier in case the night mode is not required and the integrator feels comfortable with the default on/off brightness levels. On the other hand, customising these modes and levels involves a set of parameters, as explained next. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... - Page 42 (“Normal” or “Night”) will be active after an ETS Download (parameter “LED Brightness Mode after ETS Download”). In addition, two non-exclusive checkboxes (under “LED Brightness Control”) let the integrator select how to switch from one mode to another: http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 43 Scene Object: when marked, it will be possible to switch the mode by writing a certain scene value to “[General] Scene: Receive”. Two specific textboxes will show up to enter what scenes (1 through 64) will trigger each mode. Figure 29 General - LED Brightness: Night Mode. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
-
Page 44: Welcome Back Object
Additional Condition: sets if sending the welcome back object should also depend on an external condition. The option by default is “No Additional Condition”. The following are available too: http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... - Page 45 (through “[General] Scene: send”) when the welcome back function is triggered and the condition (if any) evaluates to true. The desired scene number (1 through 64) should to be entered in “Value”. Figure 31 General - Welcome Back Object - Custom Configuration. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
-
Page 46: Locking The Touch Panel
Scene Object: when marked, two specific textboxes will show up to enter the scene numbers (1 - 64) that should trigger each action. These values are to be received through the general “[General] Scene: Receive” object. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... -
Page 47: Sounds
On the other hand, if that parameter is set to “Custom”, a specific tab named “Sounds” will show up in the tab tree on the left. The initial configuration of this screen is equivalent to the aforementioned default option. However, the following parameters will be configurable. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... - Page 48 Alarm Object: enables or disables the alarm function. If enabled, a specific object (“[General] Sounds: Alarm”) will be included into the project topology. The values (1 or 0) that will trigger the alarm sequence and then stop it must be entered in “Value”. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
- Page 49 Touch-MyDesign Plus Figure 35 General - Sounds: custom configuration. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/...
-
Page 50: Inputs
Motion Detector, to connect a motion detector (models ZN1IO-DETEC-P and ZN1IO-DETEC-X from Zennio). Important: older models of the Zennio motion detector (e.g., ZN1IO-DETEC and ZN1IO-DETEC-N) will not work properly with Touch-MyDesign Plus. For detailed information about the functionality and the configuration of the related parameters, please refer to the following specific manuals, all of them available at the Zennio homepage (www.zennio.com):... -
Page 51: Thermostat
Touch-MyDesign Plus 2.8 THERMOSTAT Touch-MyDesign Plus implements one Zennio thermostat which can be enabled and fully customised. Please refer to the specific manual “Zennio Thermostat in Touch-MyDesign Plus” (available at the Zennio homepage, www.zennio.com) for detailed information about the functionality and the configuration of the related parameters. -
Page 52: Internal Temperature Sensor
KNX bus and of triggering certain actions when the temperature reaches certain values. Please refer to the specific manual “Internal Temperature Sensor in Touch- MyDesign Plus” (available at the Zennio homepage, www.zennio.com) for detailed information about the functionality and the configuration of the related parameters. http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com/... -
Page 53: Annex I: Communication Objects
C - - W - 1 Bit DPT_Enable [General] Sounds: Enable 0 = Disable; 1 = Enable 14, 24, 34, 44, 1 Bit C T - W - [Xn] Binary Control: "0" 1-bit Generic Control DPT_Switch http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com... - Page 54 0, 1 = Stop Shutter DPT_Trigger 0x0 (Stop) 16, 26, 36, 46, 0x1 (Dec.by 100%) 4 Bit C T - - - [X] Light Dimming 4-bit Dimming Control DPT_Control_Dimming 21, 31, 41, 51 0x2 (Dec.by 50%) 0x3 (Dec.by 25%) http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com...
- Page 55 DPT_Value_1_Ucount 0 - 255 0 – 255 55, 60, 65, 70, (Unsigned Int) 1 Bit C T - W - [Zn] Stop Shutter / Step 0 = Stop Shutter / Step Up; 1 = Stop DPT_Step http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com...
- Page 56 Sending of 0 (Up) 1 Bit C T - - - DPT_UpDown [In] [Short Press] Move Down Shutter Sending of 1 (Down) C T - - - 1 Bit DPT_UpDown [In] [Short Press] Move Up/Down Shutter Switching 0/1 (Up/Down) http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com...
- Page 57 1 Bit C T - - - [In] [Long Press] Move Up/Down Shutter Switching 0/1 (Up/Down) DPT_UpDown 1 Bit C T - - - [In] [Long Press] Stop/Step Up Shutter Sending of 0 (Stop/Step up) DPT_Step http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com...
- Page 58 C T R - - [In] Presence State (Scaling) 0-100% DPT_Scaling 0% - 100% Auto, Comfort, Standby, Economy, 1=Comfort C T R - - 109, 133 1 Byte DPT_HVACMode [In] Presence State (HVAC) 2=Standby Building Protection http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com...
- Page 59 C - - W - 1 Bit DPT_Trigger [T1] Comfort Prolongation 0 = Nothing; 1 = Timed Comfort 1=Comfort 1 Byte C T R - - √ [T1] Special Mode Status 1-byte HVAC Mode DPT_HVACMode 2=Standby http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com...
- Page 60 C T R - - [T1] PI State (Cool) DPT_Switch than 0% 0 = PI signal 0%; 1 = PI signal greater 1 Bit C T R - - [T1] PI State (Heat) DPT_Switch than 0% http://www.zennio.com Technical Support: http://zennioenglish.zendesk.com...
- Page 61 Join and send us your inquiries about Zennio devices: http://zennioenglish.zendesk.com Zennio Avance y Tecnología S.L. C/ Río Jarama, 132. Nave P-8.11 45007 Toledo (Spain). Tel. +34 925 232 002. Fax. +34 925 337 310. www.zennio.com info@zennio.com...