Advertisement
Installation Instructions
TGS03 Salt Spreader
Safety Precautions
WARNING
Observe the following Safety Precautions before,
during and after operating this spreader. By following
these precautions and common sense, possible injury
to persons and potential damage to this machine may be
avoided.
1. Read this entire Installation Instruction before
operating this spreader.
2. Read all safety decals on the spreader before
operating.
3. Verify that all personnel are clear of the
spreader spray area before starting or operating this
spreader.
4. Do not adjust, clean, lubricate or unclog material
jams without first turning off the spreader.
5. Make sure the spreader is securely fastened to
the vehicle in accordance with this manual.
6. Do not operate a spreader that is in need of main-
tenance or repairs.
7. Always disconnect the battery before removing or
replacing electrical components.
Spreader Assembly
Check contents of box against parts list to make
sure all components are included. When ordering
replacement or spare parts refer to parts list for part
numbers.
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • saltdogg.com
SPREADER WARRANTY
This warranty replaces all previous warranties and
no employee of this company is authorized to extend
additional warranties, or agreements, or implications
not explicitly covered herein.
Buyers Products Company warrants all parts of
the product to be free from defects in material and
workmanship for a period of one (1) year. Parts must be
properly installed and used under normal conditions.
Normal wear is excluded.
Any part, which has been altered, including
modifications, misuse, accident, or lack of maintenance
will not be considered under this warranty.
The sole responsibility of Buyers Products Company
under this warranty is limited to repairing or replacing
any part(s), which are returned, prepaid, 30 days after
such defect is discovered, and returned part(s) are
found to be defective by Buyers Products Company.
Authorization from Buyers Products Company must
be obtained before returning any part. The following
information must accompany defective parts returned
to Buyers Products Company: RMA #, spreader model,
serial number, date installed, and distributor from
whom purchased.
Buyers Products Company shall not be liable for
damage arising out of failure of any unit to operate
properly, or failure, or delay in work, or for any
consequential damages. No charges for transportation
or labor performed on any part will be allowed under
this warranty.
9
9049 Tyler Blvd. • Mentor, Ohio 44060
—continued inside
Advertisement
Table of Contents
Related Manuals for Salt Dogg TGS03
Summary of Contents for Salt Dogg TGS03
-
Page 1: Safety Precautions
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com Installation Instructions TGS03 Salt Spreader Safety Precautions WARNING Observe the following Safety Precautions before, during and after operating this spreader. By following... - Page 2 1. Slide frame #3019400 into hitch receiver. Fig.1. Fig. 1 2. Slide hopper assembly #3019372 between frame uprights with front portion rested on the truck’s bumper. Fig.2. Fig. 2...
- Page 3 3. Align holes in rear portion of the hopper with 4. Slide hopper and frame towards tailgate leaving slots in frame uprights. Use slots which will position about 3/8” to ½” space. Align closest holes in hitch spreader with a slight upward tilt. Secure hopper receiver with holes in frame.
-
Page 4: Washer Flat
8. Attach spinner protector #3018923 to spreader frame 7. Attach shield #3015707 to trough bracket as shown as shown in Fig.8. in Fig.7 Fig. 7 SCREW 3/8-16 X 1.0 WASHER FLAT 3/8 SCREW 3/8-16 X 2.0 NUT NYLOCK 3/8-16 DISC PROTECTOR 3018923 SHIELD 3015707 WASHER FLAT 3/8... - Page 5 THIS IS WIRE GROUND ELECTRICAL SYSTEM! CAUTION NO CONNECTIONS TO TRUCK’S FRAME OR BODY DO NOT MOUNT CONTROLLER IN THE WAY OF AIR ALLOWED! BAG DEPLOYMENT! NOTE: Always disconnect battery before attempting to install electrical components on your vehicle. Mount the controller in a convenient location in the truck cab.
-
Page 6: Maintenance Instructions
Spreader Operation. Controller Warnings. 1. Due to the rate at which materials absorb mois- Check controller instruction sheet for latest controller ture differently, some materials may not perform as updates, troubleshooting codes. Controller instruction desired. Therefore, the substitution of an alternative sheet is inside controller shipping box. -
Page 7: Bill Of Materials
TGS03 Tailgate Auger Bill of Materials ITEM PART NO. QTY. DESCRIPTION 3019372 HOPPER ASSEMBLY TGS03 3019400 FRAME TGS03 3019410 LID TGS03 3019561 SPINNER, 12 IN TGS 3015707 SHIELD TGS07 3018923 DISC PROTECTOR 3019408 HARDWARE BAG TGS03 TGS03 Hopper Assembly Bill of Materials ITEM PART NO. - Page 8 PIN CLEVIS, 1/4 X 2.5 FNE038016044 NUT, NYLOCK 3/8-16 X 7/16 ZINC 3018421 ANTI SEIZE LUBRICANT POUCH 5 GRAM FPC007800075 COTTER PIN, 5/64 X 3/4 3019688 INSTRUCT ION MANUAL TGS03 HP6253WC1 PIN, 5/8 HITCH 0203700 WIRE ASSEMBLY, 36 LONG 3019688 Rev. A...