Table of Contents
Advertisement
17" LCD Open frame SAW TM （the Water-proof Type） User Guide (Rev1.0)
17" LCD Open frame SAW Touch Monitor
（ （ （ （ the Water-proof Type） ） ） ）
User Guide
Rev1.0
KOT-0170US-SA3W
KOT-0170US-SA4W
KOT-0170US-SA6W
Shenzhen KeeTouch Electronic Co., Ltd.
www.keetouch.com
June 2006
KeeTouch all rights reserved. The information in this document is subject to change without notice
- 1 -
Advertisement
Table of Contents
Summary of Contents for keetouch KOT-0170US-SA3W
- Page 1 （ （ （ （ the Water-proof Type） ） ） ） User Guide Rev1.0 KOT-0170US-SA3W KOT-0170US-SA4W KOT-0170US-SA6W Shenzhen KeeTouch Electronic Co., Ltd. www.keetouch.com June 2006 KeeTouch all rights reserved. The information in this document is subject to change without notice - 1 -...
-
Page 2: Table Of Contents
Touchmonitor Safety .............................15 Care and Handling of Your Touchmonitor ....................15 Appendix C Specification ..............................16 Mechanical Dimensions ..........................17 How to contact us ……………………………………………………………………………..…….18 KeeTouch all rights reserved. The information in this document is subject to change without notice - 2 -... -
Page 3: Introduction
Finger or gloved hand operation • Dual USB/Serial touch interface port • Worldwide agency approvals For full Product Specifications refer to Appendix C. KeeTouch all rights reserved. The information in this document is subject to change without notice - 3 -... -
Page 4: Installation And Setup
One Video cable One Brick power supply One Driver software CD One Serial cable One USB cable Eight M4 Screws and Washers KeeTouch all rights reserved. The information in this document is subject to change without notice - 4 -... -
Page 5: Product Overview
3 Place two M4 screws in the holes and with the screwdriver, screw them in to secure the bracket. 4 Repeat steps 2 and 3 to attach the other L-bracket to the other side of the touchmonitor. KeeTouch all rights reserved. The information in this document is subject to change without notice - 5 -... -
Page 6: Vesa Mounting Interface
Interface (FPMPMITM) Standard which defines a physical mounting interface for flat panel monitors, and corresponding standards for flat panel monitor mounting devices, such as wall and table arms. KeeTouch all rights reserved. The information in this document is subject to change without notice - 6 -... -
Page 7: Interface Connection
2. Connect one end of the video cable to the rear side of computer and the other to the LCD monitor. Tighten by turning the two thumb screws clockwise to ensure proper grounding. KeeTouch all rights reserved. The information in this document is subject to change without notice - 7 -... -
Page 8: Installing The Driver Software And Calibration
NOTE:Your touchmonitor have dual USB and Serial(RS232) touch interface port, Depending upon whether you connected the USB communication cable or the KeeTouch all rights reserved. The information in this document is subject to change without notice - 8 -... -
Page 9: Calibration
Desk-Top,then choose “calibrate”in the pop-out of the menu ,and choose the “RS232” or “USB” at the submenu, as follow： KeeTouch all rights reserved. The information in this document is subject to change without notice - 9 -... - Page 10 Windows will pop-out the calibration interface, then click “+” with finger one by one, as follow: After clicking the “+” on by one, the calibration is completed. KeeTouch all rights reserved. The information in this document is subject to change without notice - 10 -...
-
Page 11: Operation
1)Enter brightness adjustment. 2)Increase value of the adjustment item. 3)Select item counter-clockwise. 3 Power LED 4 Power Switches the power of the monitor KeeTouch all rights reserved. The information in this document is subject to change without notice - 11 -... -
Page 12: Controls And Adjustment
NOTE: The monitor automatically goes through the Power Management System (PMS) steps when it is idle. To activate the monitor, press any key on the keyboard or move the mouse. KeeTouch all rights reserved. The information in this document is subject to change without notice - 12 -... -
Page 13: Troubleshooting
768. See Appendix A for more information on resolution. Touch doesn’t work Make sure the touch cable is securely attached at both ends. KeeTouch all rights reserved. The information in this document is subject to change without notice - 13 -... -
Page 14: Appendix A Native Resolution
LCD pixels. Poor fidelity conversion can result in artifacts in the LCD displayed image such as varying width characters. KeeTouch all rights reserved. The information in this document is subject to change without notice - 14 -... -
Page 15: Appendix B Touchmonitor Safety
• To clean the touchscreen, use window or glass cleaner. Put the cleaner on the rag and wipe the touchscreen. Never apply the cleaner directly on the touchscreen. KeeTouch all rights reserved. The information in this document is subject to change without notice - 15 -... -
Page 16: Appendix C Specification
Frequency（ （ （ （ H/V） ） ） ） 30～80KHz / 60～75Hz Type: External brick Power Supply Input (line) voltage: 100-240 VAC, 50-60 Hz KeeTouch all rights reserved. The information in this document is subject to change without notice - 16 -... -
Page 17: Mechanical Dimensions
5 years for SAW Sensor; 3 years for controller; 1 year for LCD NOTE:The display SPEC. will change follow the relevant LCD panel brand and model Mechanical Dimensions KeeTouch all rights reserved. The information in this document is subject to change without notice - 17 -... -
Page 18: How To Contact Us
+86-755-81709579 ： ： ： ： Sales & Marketing sales@keetouch.com ： ： ： ： Technical Support support@keetouch.com ： ： ： ： Webmaster webmaster@keetouch.com KeeTouch all rights reserved. The information in this document is subject to change without notice - 18 -...