Harman XXV Owner's Manual page 16
Hide thumbs
Also See for XXV:
- Installation & operating manual (44 pages) ,
- Owner's manual (44 pages) ,
- Owners manual care and operation (35 pages)
Advertisement
Helpful Hints
I. Fines are small pieces of broken pellets (sawdust). Fines do not
flow easily and offen build up on the hopper funnel bottom angles.
You can push these fines into the feeder opening and then fill the
hopper with pellets. As the system works, they will be burned. Or
you can clean them out before filling the hopper.
2. The "TEST cycle will operate the feeder motor for exactly one
lgniter Switch to"AUTO"(up position)
Make sure the unit is plugged into a 120 VAC, 60
HZ electrical source. The power light should be the
only light lit.
1. Turn Mode Selector to "OFF".
2. Fill hopper with pe1lets.l
3. Clean burn pot with scraper, if necessary5
4. If starting after an empty hopper, turn Feed
Adjuster to "TEST" (for one 60 second c y ~ l e ) . ~
This
will purge pellets into the auger tube and also allow
you to check the motors for operation.
NOTE: The auger motor will not operate with
the view door or ash pan door open.3
5. Turn Feed Adjuster to #4.4
6. Flip the Igniter Switch up into the "AUTO"
position.
minute. Tuming to "TEST again and again may purge too much
fuel into the bum pot causing excessive smoke on start-up.
7.
Turn the Temperature Dial to desired room
3. The firebox low pressure switch will not allow the auger motor or
temperat~re.
the igniter element to operate if the view door or the ash pan door
are open.
4. Adjust Feed Rate. If this is your first fire or you are trying different
8. Turn Mode Selector to Room Temperature or
pellets, set the feed adjuster to #4, Fig. 22. This is a conservative
Stove Temperature.
number and will probably need to be increased. Affer you know a
feed rate
your feed
5. This is
setting that works well, use that Setting. Remember; if
9
Fill hopper with pellets and remove ashes as
rate is too high you may waste fuel.
usually a weekly maintenance procedure. Cleaning the
req~ired.~
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes on the front of the
bum pot into the ash pan. Then, scrape the top surface of the bum
pot downward into the base of the bum pot, When the stove is
ignited these scrapings will be pushed out by the feeder and
burned.
6. The ash pan can hold the ashes from approximately I ton of
premium fuel. This means the ashes will only need to be emptied
a few times a year.
7, Setting the feed adjuster # for maximum bum: With the unit
buming in 'XUTO", turn to "Stove Mode" and put the fan on "H". Set
the Temperature Dial to #7. Allow the unit to burn for about 30
minutes and check ash on front of burn pot. Fig. 23. If the ash line
is larger than I", turn the feed adjuster from #4 to #5. Allow another
30 minutes of bum time and check again. I f , at #6 setting, a I" or
less ash bed is not obtainable, it is not a problem. The 1" ash bed
is only a maximum burn rate and at most normal settings the ash
bed will be larger.
WARNING
"NEVER USE GASOLINE, GASOLINE-TYPE LANTERN
FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR
SIMILAR LIQUIDS TO START OR "FRESHEN UP
"
A
FIRE IN THIS HEATER. KEEP ALL SUCH LIQUIDS
WELL AWAY FROM THE HEATER WHILE IN U S E .
ONLY USE WOOD PELLET FUEL. DO NOT BURN
GARBAGE IN STOVE.
16
XXV Pellet Stove
Advertisement
