Table of Contents
Advertisement
Connecting Power to the Cisco ASR 1013 Router
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Statement 1030
Cisco ASR 1013 Router Power Supply Overview
This section provides information about the Cisco ASR 1013 power supply input requirements and
power cable options.
The DC power supply for the Cisco ASR 1013, ASR 1006, ASR 1004, and ASR 1002 routers operate at
individual specifications.
Table 11-2
Cisco ASR 1000
Series Router DC
Power Supply
System Input Rating (Amps)
Cisco ASR 1006
40
Cisco ASR 1004
24
Cisco ASR 1002
16
Cisco ASR 1013
40
For example, the Cisco ASR 1002 Router DC power supply, with 16 Amp input rating must use an AWG #12 gauge wire for a 20 A circuit breaker and
an AWG #10 gauge wire for a 30 A circuit breaker.
Power Cords Supported by the Cisco ASR 1013 Router
The following power cords are supported by the Cisco ASR 1013 Router:
•
•
•
The Cisco ASR 1013 Router modular chassis supports redundant power entry modules (PEMs). At least
one PEM in each 1+1 redundant power supply zone must be functioning to power the zone and both
zones must be functional. In the event of a single fan failure, the remaining fans are sufficient to cool the
entire chassis although fan speed may have to be increased.
The Cisco ASR 1013 Router system is configured in a dual zone 1+1 power supply configuration. For
ASR 1013 router power consumption specifications, see the
section on page
The following items list the maximum input and output of the system power consumption for the two
power zones in the Cisco ASR 1013 Router:
•
•
•
Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation Guide
11-28
Table 11-2
Cisco ASR 1000 Series Router DC Power Supply System Input Requirements
CAB-AC20A-90L-IN—20 A AC right-angle power cord—International
CAB-4000W-US1—Power Cord, 250 VAC 20 A, Right Angle C19, NEMA 6-20 Plug, US
CAB-US520-C19-US—NEMA 5-15 to IEC-C19 14ft US
A-500.
Maximum input (DC): 4,200W
Maximum input (AC – High Line): 4,000 W
Maximum output (DC and AC – High Line): 3,390 W
Chapter 11
shows the common input ranges and circuit breaker requirements.
Circuit Breaker Amps
Minimum
Maximum
Always 50
30
40
20
30
Always 50
"Cisco ASR 1013 Router Specifications"
Cisco ASR 1013 Router Overview and Installation
AWG # Wire
Minimum
Maximum
Always AWG #6 wire
10
8
12
10
Always AWG #6 wire
OL-13208-11
Advertisement
Chapters
Table of Contents
Troubleshooting
Related Manuals for Cisco ASR 1000 series
Related Products for Cisco ASR 1000 series
- Cisco ASR1000-RP1 - ASR 1000 Series Route Processor 1 Router
- Cisco ASR1000-RP2 - ASR 1000 Series Route Processor 2 Router
- Cisco ASR-1000-SIP10
- Cisco ASR 1001
- Cisco ASR1002-5G-SEC/K9 - ASR 1002 VPN+FW Bundle Router
- Cisco ASR1004-20G-SEC/K9 - ASR 1004 VPN+FW Bundle Router
- Cisco ASR1002-10G-VPN/K9 - ASR 1002 VPN Bundle Router
- Cisco ASR1002-5G-HA/K9 - ASR 1002 HA Bundle Router