free hit counter
Pacific energy NEO 2.5 Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Pacific energy Manuals
  4. Wood stove
  5. NEO 2.5 INSERT
  6. Installation and operating instructions manual

Pacific energy NEO 2.5 Installation And Operating Instructions Manual

Hide thumbs Also See for NEO 2.5:
Table of Contents

Advertisement

Quick Links

See also: Installation Instructions and Operating Manual
IMPORTANT:
THESE INSTRUCTIONS ARE TO
REMAIN WITH THE HOMEOWNER

SAFETY NOTICE

If this stove is not properly installed, a
house fi re may result. For your safety,
follow the installation instructions. Contact
local building or fire officials about
restrictions and installation inspection
requirements in your area.
TESTED and LISTED to CAN/ULC S627
AND UL 1482
Meets the Environmental Protection
Agency's July 1990 Particulate Emission
Standards
071114-24
INSTALLATION
AND OPERATING
INSTRUCTIONS
MODEL - NEO 2.5
SERIES - A
NEO25
SERIAL #
5055.900

Advertisement

Table of Contents
loading

Related Manuals for Pacific energy NEO 2.5

Summary of Contents for Pacific energy NEO 2.5

  • Page 1: Safety Notice

    TESTED and LISTED to CAN/ULC S627 AND UL 1482 Meets the Environmental Protection Agency's July 1990 Particulate Emission Standards MODEL - NEO 2.5 SERIES - A 071114-24 NEO25 5055.900...

  • Page 2: Table Of Contents

    Optional Blower ....................15 Blower Operation ......................15 Optional Outside Air Adaptor .................... 15 Troubleshooting ....................16 Replacement Parts - NEO 2.5 ..................17 Understanding & Operating Your Pacifi c Energy Stove ............. 18 Firebrick Installation Instructions ..............19 Label ..........................23 PLEASE SAVE THESE INSTRUCTIONS NOTE: WE STRONGLY RECOMMEND THAT SMOKE DETECTORS BE INSTALLED.

  • Page 3: Safety

    Safety Creosote Formation and Need for In Case of a Chimney Fire Removal 1. Prepare to evacuate to ensure everyone's safety. Have a well understood plan of action for evacuation. Have a When wood is burned slowly, it produces tar and other organic place outside where everyone is to meet.

  • Page 4: Operation

    2. Place crumpled newspaper in the centre of the heater Your PACIFIC ENERGY heater is designed for many years of and criss-cross with several pieces of dry kindling. Add trouble free operation. Over fi ring the appliance will shorten a few small pieces of dry wood on top.

  • Page 5: Restarting After Extended Or Overnight Burns

    Restarting After Extended or Overnight Ash Removal Burns Caution: Ashes are to be removed only when the heater is cold. Whenever ashes get 3(76mm) to 4(102mm) inches deep in 1. Open door and rake hot embers towards the front of the your fi rebox, and when fi re has burned down and cooled, heater.

  • Page 6: Maintenance

    Maintenance 1. Burn cord wood only, dry and well seasoned. The denser To remove broken glass, remove the door gasket and then or heavier the wood when dry, the greater its heat value. undo the eight screws securing the gasket guides and glass This is why hardwoods are generally preferred.

  • Page 7: Maintenance Checks

    Maintenance Checks Check the following parts for damage such as cracks, excessive corrosion, burned out sections and excessive warping: (See website for descriptions and more detail) Some warping of the baffle is normal(up to 1/4” or 6mm). Replace if the baffle has permanent warping greater than this or has signs of cracking or breakage.

  • Page 8: Assembly

    NEO 2.5 Dimensions FIG. #1 24 1/2" 622mm 29" 6 1/8" 737mm 156mm 41" 1.04m 40 1/8" 1.02m Assembly Side Panel Removal/Installation 1) To remove the panels, fi rst remove the screws that secure the panel to the rear shield. Fig. #3...

  • Page 9: Ember Protection

    Combustion Air Ember Protection Intake or combustion air can be supplied to the stove in one of The stove may be installed on a combustible fl oor provided two ways. Consult your local building code or CAN/CSA-B365, ember protection made from a non-combustible material with Installation Code for Solid-Fuel-Burning Appliances and a minimum K value of 23.7 btu/ft h ˚F is used.

  • Page 10: Residential Installation

    Residential Installation Warning: Under no circumstances is this heater to be installed The chimney connector should not pass through an attic, in a makeshift or "temporary" manner. It may be fi red only roof space, closet or similar concealed space, fl oor, or after the following conditions have been met.
  • Page 11 6. Cut a hole in the ceiling and roof to suit the chimney system and frame in the sides. The chimney support is mounted to the framing. 7. Assemble chimney sections so the fi nished length is resting on the support and protruding through the roof. Avoid having joints between ceiling and roof.
  • Page 12 FIG. #7 Spark arrestor rain cap The chimney may incorporate an offset. To do this safely, all Chimney sections of listed connector, 3' (914 mm) Minimum offset elbows and chimney section must be screwed together by at least three Storm collar sheet metal screws per joint.
  • Page 13 Fireclay Flue liner FIG. #8 Concrete cap Ensure that the Masonry chimney meets all National Fire Protection Association and local building codes. Chimney Have the chimney cleaned and inspected by a professional to ensure there are no cracks, weak mortar or other signs of deterioration.

  • Page 14: Mobile Home Installation

    Mobile Home Installation Additional Requirements: Procedure: Warning: Under no circumstances is this heater to be installed CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE in a makeshift or "temporary" manner. It may be fi red only HOME FLOOR, WALL AND CEILING/ROOF MUST BE after the following conditions have been met.

  • Page 15: Optional Blower

    Optional Blower Optional Outside Air Adaptor The adaptor(OAIR.1A) is only required if outside combustion air is being used. The optional blower kit (WODC.BLOW) is equipped with a three prong power cord and may be installed at any time. Installation(OAIR.1A): Follow installation instructions supplied with the kit. Route power supply cord away from heater.

  • Page 16: Troubleshooting

    Troubleshooting Problem Cause Cure Glass is Dirty 1. Wood is wet - Use dry wood 2. Turning down air control - Do not turn down until or damper too soon a) there is a good bed of coals b) the wood is charred 3.

  • Page 17: Replacement Parts - Neo 2.5

    ....Coffee Bean Brown Enamel .... NE25.PPCBA 15 ..Ash System Front Brace ....NE25.78357 ....Copper Enamel .......NE25.PPCUA 16 ..NEO 2.5 Pedestal, Black ......NE25.PED ....Ivory Enamel ........NE25.PPIYA 17 ..Ash Dump Assembly ......NE25.7857 ....Sunset Red Enamel ......NE25.PPRDA 18 ..

  • Page 18: Understanding & Operating Your Pacifi C Energy Stove

    Understanding & Operating Your Pacifi c Energy Stove The Pacifi c Energy SUPER SERIES line of woodstoves is a culmination of years of research and development. Designed to be efficient, clean-burning and user-friendly, this heater will OPERATING TIPS give you years of warm service. However, a knowledgeable operator is still the most important factor for maximum perfor- 1.

  • Page 19: Firebrick Installation Instructions

    Firebrick Installation Instructions NEO 2.5 This package contains 18 full-size fi rebricks, as well as 6 various cut-size bricks. With the heater in the upright position, install fi rebricks as follows: - Install the rear fi rebricks, 4 full-size, two on each side of the baffl e tube.
  • Page 20 NEO25 071114-24...
  • Page 21 071114-24 NEO25...
  • Page 22 NEO25 071114-24...

  • Page 23: Label

    Label MUR COTE MUR ADJACENT SIDE WALL ADJACENT WALL COTE SIDE 071114-24 NEO25...
  • Page 24 PACIFIC ENERGY FIREPLACE PRODUCTS LTD. 2975 Allenby Rd., Duncan, B.C. V9L 6V8 For technical support, please contact your retailer. Web site: http://www.pacifi cenergy.net Printed in Canada NEO25 071114-24...

Table of Contents