Advertisement
DT2- - 800
DT2
Full Range Digital Power Amplifier
Full Range Digital Power Amplifier
2 X 200 Watts RMS- - 4 4Ω Ω
2 X 200 Watts RMS
2 X 400 Watts RMS
2 X 400 Wa
tts RMS- - 2 2Ω Ω
Ultimate Sound, Inc.
138 University Parkway
Pomona, CA 91768
Toll Free: 888-909-9988
Telephone: 909-594-2604
Fax: 909-594-0191
800
INTRODUCTION
I. Description
This device is a high power, audio amplifier. Use it responsibly. Very
loud music can cause permanent hearing loss. This amplifier is intended
for installation in vehicles with a 12 Volt, negative ground electrical
system. Attempting to connect or operate the amplifier in another type of
electrical system may cause damage to the amplifier or the electrical
system.
II. About This Manual
Read the Instructions-
Be sure that you have read all operating instructions and understand all
safety precautions before installing and operating the amplifier. We
Digitalis
Digitalis
recommend that you have your
specialist.
Follow the Instructions-
The instructions are intended to help you safely obtain the best
performance from the amplifier. Carefully follow all installation and
operating instructions.
Save the Operating Manual-
Keep the manual in a safe place after installing the amplifier. You may
have questions later.
Text Conventions used in this Manual-
Bold-
Headings and important information.
Bold, Underlined-
Very important information.
"Bold"-
As labeled on the amplifier, or quoted from elsewhere in this
manual.
III. Safety and Operating Precautions-
Caution!
This symbol warns the user of a potential risk or hazard if instructions are
not followed.
⇒ This arrow symbol points to a specific instruction for avoiding a
potential hazard.
amplifier installed by a
ii
Advertisement
Table of Contents
Related Manuals for Ultimate Sound DT2-800
Summary of Contents for Ultimate Sound DT2-800
- Page 1 Caution! This symbol warns the user of a potential risk or hazard if instructions are not followed. ⇒ This arrow symbol points to a specific instruction for avoiding a Ultimate Sound, Inc. 138 University Parkway potential hazard. Pomona, CA 91768...
-
Page 2: Installation
Step 3- Run a remote turn on cable from the switched +12V source you Installation will be using to turn on the system components. This may be a toggle switch, a relay, or your source unit’s remote trigger wire, or power antenna trigger wire. -
Page 3: Bridged Mono
Simultaneous stereo and mono operation, “2+1 Mode”, requires a passive MULTIPLE SPEAKER CONNECTION crossover to send low frequencies to the mono speaker and higher frequencies to the stereo speakers. The following table lists the PARALLEL- Each additional speaker decreases the load impedance component values for a 6 dB/Octave crossover at common frequencies for the amplifier. -
Page 4: Operation
filter. If both buttons are in the “OFF” position, the amplifier is Installation- Check all Connections operating full range. If both switches are pushed in, the amplifier is in the Recheck all connections before reconnecting the negative(-) battery cable. band-pass mode. Insert the correct value fuse in the fuse holder at the battery before attempting to turn on the system. -
Page 5: Features And Specifications
Features and Specifications: DT2- - 800 Operation- Location of Terminals, Controls and LED indicators 2Ω Ω Stable 1. RCA input jacks 2. Input attenuator 3. Input level adjust Bridgeable Yes, 4Ω 4. Bass Boost 5. High pass freq. 6. High pass on/off Tri-mode 7. -
Page 6: Troubleshooting
Troubleshooting: Condition Possible Cause Possible Solution No sound Low or no remote turn Check the remote turn on on voltage, or no remote connection and the voltage at turn on connection the amplifier and source unit Blown fuse(s) Check all system fuses Wiring problems Recheck all connections Check for short circuits...