http://www.xiaoyu163.com 3 7 63 1515 0 SERVICE MANUAL CD RECEIVER MA043 2004 KD-AR5000,KD-LHX500 Area suffix J -------------- Northern America KD-AR5000 KD-LHX500 L 13942296513 KD-AR5000J LHX500J ARSENAL rogo LINE IN TABLE OF CONTENTS PRECAUTIONS ............... 1-3 SPECIFIC SERVICE INSTRUCTIONS .
Page 2
http://www.xiaoyu163.com 3 7 63 1515 0 SPECIFICATION AUDIO AMPLIFIER SECTION Maximum Power Output Front 50 W per channel Rear 50 W per channel 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than Continuous Power Output (RMS) Front 0.8% total harmonic distortion.
http://www.xiaoyu163.com SECTION 1 3 7 63 1515 0 PRECAUTIONS Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 4
http://www.xiaoyu163.com Preventing static electricity 3 7 63 1515 0 Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.2.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
http://www.xiaoyu163.com SECTION 2 3 7 63 1515 0 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. L 13942296513 u163 (No.MA043)1-5 http://www.xiaoyu163.com...
http://www.xiaoyu163.com SECTION 3 3 7 63 1515 0 DISASSEMBLY Main body section 3.1.1 Removing the front panel assembly (See Fig.1) (1) Push the detach button in the lower right part of the front Front panel assembly panel assembly. (2) Remove the front panel assembly. Detach button Fig.1 3.1.2 Removing the heat sink...
Page 7
http://www.xiaoyu163.com 3.1.3 Removing the top chassis assembly 3 7 63 1515 0 (See Figs.3 to 6) • Prior to performing the following procedures, remove the heat Bottom chassis assembly sink. Reference: Remove the front panel assembly as required. (1) From the bottom side of the main body, remove the two screws C attaching the top chassis assembly to the bottom chassis assembly.
http://www.xiaoyu163.com 3.1.4 Removing the front chassis 3 7 63 1515 0 (See Figs.7 and 8) • Prior to performing the following procedure, remove the front Top chassis assembly panel assembly, heat sink and top chassis assembly. (1) From the both sides of the top chassis assembly, remove the two screws E attaching the front chassis.
Page 9
http://www.xiaoyu163.com 3.1.6 Removing the CD mechanism assembly (See Fig.10) 3 7 63 1515 0 Top chassis • Prior to performing the following procedures, remove the front panel assembly, heat sink and top chassis assembly. Reference: Remove the mechanism control board as required. (1) From the inside of the top chassis assembly, remove the three screws G attaching the CD mechanism assembly.
http://www.xiaoyu163.com 3.1.8 Removing the rear bracket 3 7 63 1515 0 (See Fig.13) • Prior to performing the following procedures, remove the front Wire Main board panel assembly, heat sink, top chassis assembly and main board. Wire (KD-AR5000) Wire holder (1) From the rear side of the main board, remove the wires from the rear bracket in the direction of the arrow.
Page 11
http://www.xiaoyu163.com 3.1.10 Removing the front board 3 7 63 1515 0 Rear cover assembly (See Figs.15 to 17) • Prior to performing the following procedures, remove the front panel assembly. (1) From the rear side of the front panel assembly, remove the four screws P attaching the rear cover assembly to the front panel assembly.
Page 12
http://www.xiaoyu163.com CD Mechanism section 3 7 63 1515 0 3.2.1 Removing the top cover (See Figs.1 and 2) (1) Remove the four screws A on the both side of the body. (2) Lift the front side of the top cover and move the top cover backward to release the two joints a.
http://www.xiaoyu163.com 3.2.2 Removing the connector board 3 7 63 1515 0 Wires (See Figs.3 to 5) CAUTION: Before disconnecting the flexible wire from the pickup, solder the short-circuit point on the pickup. No observance of this in- struction may cause damage of the pickup. (1) Remove the screw B fixing the connector board.
Page 14
http://www.xiaoyu163.com 3.2.3 Removing the DET switch 3 7 63 1515 0 (See Figs.6 and 7) (1) Extend the two tabs c of the feed sw. holder and pull out the switch. (2) Unsolder the DET switch wire if necessary. switch Connector board Pickup...
Page 15
http://www.xiaoyu163.com 3.2.4 Removing the chassis unit 3 7 63 1515 0 (See Figs.8 and 9) • Prior to performing the following procedure, remove the top Chassis unit cover and connector board. Suspension spring (L) (1) Remove the two suspension springs (L) and (R) attaching Suspension spring (R) the chassis unit to the frame.
http://www.xiaoyu163.com 3.2.5 Removing the clamper assembly 3 7 63 1515 0 (See Figs.10 and 11) • Prior to performing the following procedure, remove the top cover. (1) Remove the clamper arm spring. Clamper arm (2) Move the clamper assembly in the direction of the arrow to spring release the two joints d.
Page 17
http://www.xiaoyu163.com 3.2.6 Removing the loading / feed motor assembly 3 7 63 1515 0 (See Figs.12 and 13) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw C and move the loading / feed motor as- sembly in the direction of the arrow to remove it from the chassis rivet assembly.
Page 18
http://www.xiaoyu163.com 3.2.7 Removing the pickup unit 3 7 63 1515 0 Pickup unit (See Figs.14 to 18) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw D and pull out the pu. shaft holder from the pu.
Page 19
http://www.xiaoyu163.com 3.2.9 Removing the trigger arm 3 7 63 1515 0 Joint k (See Figs.19 and 20) • Prior to performing the following procedure, remove the top cover, connector board and clamper unit. (1) Turn the trigger arm in the direction of the arrow to release Trigger arm the joint k and pull out upward.
Page 20
http://www.xiaoyu163.com 3.2.11 Removing the mode sw. / select lock arm 3 7 63 1515 0 Link plate Joint t (See Figs.22 and 23) Mode sw. • Prior to performing the following procedure, remove the top plate assembly. Select lock arm (1) Bring up the mode sw.
Page 21
http://www.xiaoyu163.com 3.2.12 Reassembling the mode sw. / select lock arm 3 7 63 1515 0 Select lock arm spring (See Figs.24 to 26) REFERENCE: Hook w Reverse the above removing procedure. (1) Reattach the select lock arm spring to the top plate and set Joint v Joint v the shorter end of the select lock arm spring to the hook w...
Page 22
http://www.xiaoyu163.com 3.2.13 Removing the select arm R / link plate 3 7 63 1515 0 Link plate Joint c' Joint r (See Figs.27 and 28) Select arm R Joint b' • Prior to performing the following procedure, remove the top plate assembly.
Page 23
http://www.xiaoyu163.com 3.2.15 Removing the loading roller assembly 3 7 63 1515 0 (See Figs.31 to 33) Loading roller assembly • Prior to performing the following procedure, remove the Roller guide clamper assembly and top plate assembly. spring (1) Push inward the loading roller assembly on the gear side and detach it upward from the slot of the joint g' of the lock arm rivet assembly.
Page 24
http://www.xiaoyu163.com 3.2.16 Removing the loading gear 5, 6 and 7 3 7 63 1515 0 (See Figs.35 and 36) Loading gear bracket • Prior to performing the following procedure, remove the top cover, chassis unit, pickup unit and top plate assembly. Loading gear 6 (1) Remove the screw K attaching the loading gear bracket.
Page 25
http://www.xiaoyu163.com 3.2.17 Removing the gears 3 7 63 1515 0 Joint p' (See Figs.37 to 40) • Prior to performing the following procedure, remove the top Change plate cover, chassis unit, top plate assembly and pickup unit. rivet assembly • Pull out the loading gear 3. (See Fig.35.) (1) Pull out the feed gear.
Page 26
http://www.xiaoyu163.com 3.2.18 Removing the turn table / spindle motor 3 7 63 1515 0 Turn table (See Figs.41 and 42) • Prior to performing the following procedure, remove the top cover, connector board, chassis unit and clamper assembly. (1) Remove the two screws L attaching the spindle motor as- sembly through the slot of the turn table on top of the body.
(3) Digital tester Output Level Line out 2.0V (Vol. MAX) (4) Tracking offset meter (5) Test Disc JVC :CTS-1000 Dummy load (6) Extension cable for check Exclusive dummy load should be used for AM,and FM. For FM EXTSH002-22P × 1 dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered since...
http://www.xiaoyu163.com SECTION 5 3 7 63 1515 0 TROUBLESHOOTING Feed section Is 5v or 0V at IC621 Is the wiring for IC621 Is 5V present at IC681 Check CD8V. pin 40? pin 40 correct? pin 6? Check the vicinity of IC621.
Page 29
http://www.xiaoyu163.com Signal processing section 3 7 63 1515 0 Compare the L-ch and Is the sound output from No sound from either R-ch to locate the both channels (L, R)? channel. defective point. Normal Is 9V present at IC365 Is 9V present at IC901 Check IC901 and its pin 16? pin 10?
http://www.xiaoyu163.com Maintenance of laser pickup 3 7 63 1515 0 Replacement of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens Turn of the power switch and, disconnect the with a alcohol soaked cotton swab.
Page 31
http://www.xiaoyu163.com Service mode 3 7 63 1515 0 5.8.1 Service mode setting (1) Push POWER BOTTON (Power ON) (2) Set to service mode By pushing and holding "DISP" + "VOLUME +" + touch panel "upper right" sequentially. "DISP" button "VOLUME +" button TUNER No Name FLAT...
Page 32
http://www.xiaoyu163.com 3 7 63 1515 0 ROM COLLECTION Don't used DATA DATA READ CLEAR BACK DATA READ (No disc) PLEASE INSERT DATA CD BACK DATA READING NOW . . . DATA CLEAR DON'T TOUCH ANY KEY SUCCESS SUCCESS!! PLEASE EJECT CD Return to normal display five seconds after FALL...
Page 33
http://www.xiaoyu163.com 3 7 63 1515 0 CD ERROR CLEAR EPROM (CD ERROR) clear Error code history elimination NOW . . . CD ERROR CLEAR BACK CH ERROR CLEAR EPROM (CH ERROR) clear Error code history elimination NOW . . . CH ERROR CLEAR BACK MECHA ERROR CLEAR...
Page 34
http://www.xiaoyu163.com 3 7 63 1515 0 RDS_ENGINNER (ADJUST) EPROM VIEW SYNC SYNC Default Enter EPROM ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** BACK BACK Default Enter ***** BACK Default Enter *****...
Page 35
http://www.xiaoyu163.com 3 7 63 1515 0 AUTO ADJ MANUAL ADJ AUTO ADJ It is not used for the item used inside at the time of manufacture. AUTO ADJ AUTO ADJ FM DAA FM DAA 87.5MHz 40dBuV 0% 87.5MHz 40dBuV 0% No Signal BACK BACK...
Page 36
http://www.xiaoyu163.com 3 7 63 1515 0 MANUAL ADJ It will be used if ther are directions. MANUAL ADJ Press here MANUAL FM DAA FM DAA 87.5MHz 40dBuV 0% 87.5MHz 40dBuV 0% No Signal BACK BACK MANUAL ADJ Press here MANUAL FM DAA FM DAA 97.9MHz...
Page 37
http://www.xiaoyu163.com 5.8.2 Detailed CD error code 3 7 63 1515 0 Error Details of error Error code Detailed error code Pickup movement error Time over at PUBWD and PUFWD by monitoring RESET SW Pickup cannot move in an inner 1.Time over of pickup movement 0051 in an inner direction(10s) direction.RESET SW is not on...
Page 38
http://www.xiaoyu163.com 5.8.3 Detailed error code of mechanism error 3 7 63 1515 0 Error Details of error Error code Detailed error code Disc loading error 1.B1 Time out 0011 0012 2.B2 Time out 0013 3.C1 Time out 0014 4.C2 Time out 5.D1 Time out 0015 0016...
Page 39
http://www.xiaoyu163.com 5.8.4 Changer mechanism error display 3 7 63 1515 0 Symptom Details Error code Detailed error code Tray motor TIME OVER Tray eject error 1.TRAYINSW TIME OVER Tray motor does not operate. 0011 (TRAYINSW:L,TRAYOUTSW:H) 2.TRAYOUTSW TIME OVER Tray stops. 0012 (TRAYINSW:H,TRAYOUTSW:H) 3.TRAYINSW TIME OVER...
Page 40
http://www.xiaoyu163.com 5.8.5 Error codes of panel mechanism 3 7 63 1515 0 Error display in Error display in Error service mode normal condition Error in OPEN (Abnormal OPEN) 1. OPEN cannot be detected. TIME OUT 0A01 Error in CLOSE (Abnormal ANGLE1) 1.
Page 41
http://www.xiaoyu163.com 5.8.7 16 PIN CORD DIAGRAM-1 3 7 63 1515 0 Black Green OR/WH Violet BL/WH Gray Blue WH White Yellow WH/BK Orange GN/BK VI/BK GY/BK MEMORY 16 YL 8 BK 7 RD 15 OR/WH 3 GN 11 GN/BK L 13942296513 2 VI 10 VI/BK 4 WH...
Page 42
http://www.xiaoyu163.com 5.8.8 16 PIN CORD DIAGRAM-2 3 7 63 1515 0 OR/WH Black Green BL/WH Violet Blue Gray WH/BK White Yellow GN/BK Orange VI/BK GY/BK MEMORY 16 YL 8 BK 7 RD 15 OR/WH REMOTE 5 BL/WH 3 GN L 13942296513 11 GN/BK 2 VI 10 VI/BK...
Page 44
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.MA043) Printed in Japan http://www.xiaoyu163.com...
http://www.xiaoyu163.com 3 7 63 1515 0 SCHEMATIC DIAGRAMS CD RECEIVER KD-AR5000,KD-LHX500 CD-ROM No.SML200403 Area suffix J -------------- Northern America KD-AR5000 L 13942296513 KD-LHX500 KD-AR5000J LHX500J ARSENAL rogo LINE IN Contents Block diagram u163 2-3 to 22 Standard schematic diagrams 2-23 to 26 Printed circuit boards No.MA043SCH COPYRIGHT...
http://www.xiaoyu163.com 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 47
http://www.xiaoyu163.com 3 7 63 1515 0 < M E M O > L 13942296513 u163 http://www.xiaoyu163.com...
http://www.xiaoyu163.com 3 7 63 1515 0 Block diagram VA,VB IC573 VE,VF MD,LD X571 IC601 VREF RWSEL,IOP CLOCK GEN. CD RF RFGC REST REST RF,FE,TE SWITCH RFRP SEL,TEB RFDC LOAD/FEED+ DATA LOAD/FEED REST,SW1,SW2 LOAD/FEED- MOTOR CDSDO LRCK CDBCK IC652 CDLRCK BUS0 to BUS3 SPINDLE+ BUCK,CCE MP3 DEC...
Page 49
http://www.xiaoyu163.com 3 7 63 1515 0 CN345 BUSENABLE FRONT IC191 IC171 DSP_TUNER_IIC_SDA LINE OUT DSP_TUNER_IIC_SCL IC291 IC271 RESET_7730 REAR MIX AMP LINE AMP FM/AM LINE OUT OUT FL TUNER OUT RL FL+, FL- KAGC1 OUT FR FR+, FR- DAC_FL AF_SAMPLE1 OUT RR RL+, RL- DAC_FR...
Page 74
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.MA043SCH) http://www.xiaoyu163.com...
http://www.xiaoyu163.com 3 7 63 1515 0 PARTS LIST [ KD-AR5000 / KD-LHX500 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix J -------------- Northern America L 13942296513 - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1) 3- 5 CD mechanism assembly and parts list (Block No.MB)
Page 76
http://www.xiaoyu163.com 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. Main board L 13942296513 Mecha control board Front board 60 59 u163 http://www.xiaoyu163.com...
Page 77
http://www.xiaoyu163.com 3 7 63 1515 0 k No. 89 45 93 91 Main board L 13942296513 60 59 u163 http://www.xiaoyu163.com...
Page 78
http://www.xiaoyu163.com 3 7 63 1515 0 General Assembly Symbol No. Part No. Part Name Description Local Block No. [M][1][M][M] AR50 LV34702-002A VOLUME FITTING Symbol No. Part No. Part Name Description Local LHX5 LV34702-001A VOLUME FITTING LV43906-001A DOUBLE FACE (x2) QUQ105-2207AE FFC WIRE...
Page 79
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism assembly and parts list Block No. Grease TN-2001-1013 TNG-87 GP-501MK CFD-005Z GP-501A L 13942296513 u163 http://www.xiaoyu163.com...
Page 80
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism Block No. [M][B][M][M] Symbol No. Part No. Part Name Description Local 30320101T FRAME 30320102T TOP COVER 30320115T DANPER F (x2) 30320116T DANPER R 303205505T CHASSIS RIVET 303205503T CHANGE P. RVT A 303205301T CLAMPER ASSY 303205302T...
http://www.xiaoyu163.com 3 7 63 1515 0 Electrical parts list Main board Symbol No. Part No. Part Name Description Local Block No. [0][1][0][0] D718 SML-310LT/MN/-X Symbol No. Part No. Part Name Description Local D719 SML-310LT/MN/-X D720 SML-310LT/MN/-X D722 UDZS5.6B-X Z DIODE 1.5kΩ...
Page 82
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local NDC31HJ-101X C CAPACITOR 100pF 50V J AR50 C1402 NCB31HK-472X C CAPACITOR 4700pF 50V K NDC31HJ-101X C CAPACITOR 100pF 50V J AR50 NCB31CK-473X...
Page 83
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local AR50 NRSA63J-101X MG RESISTOR 100Ω 1/16W J C3402 NCB31CK-473X C CAPACITOR 0.047uF 16V K NRSA63J-101X MG RESISTOR 100Ω...
Page 84
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local AR50 R1905 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R791 NRSA63J-473X MG RESISTOR 47kΩ 1/16W J R1921 NRSA63D-103X MG RESISTOR 10kΩ...
Page 85
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R4018 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R4019 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J AR50 CN341 QGA2006C1-04 CONNECTOR W-B (1-4)
Page 86
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local D8733 NSCM315C-W R8007 NRSA63J-474X MG RESISTOR 470kΩ 1/16W J D8751 UDZS6.2B-X Z DIODE R8008 NRSA63J-473X MG RESISTOR 47kΩ...
Page 87
http://www.xiaoyu163.com 3 7 63 1515 0 CD module board Symbol No. Part No. Part Name Description Local Block No. [0][3][0][0] R8301 NRSA63J-104X MG RESISTOR 100kΩ 1/16W J R8302 NRSA63J-474X MG RESISTOR 470kΩ 1/16W J Symbol No. Part No. Part Name Description Local...
Page 88
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C636 NCB31CK-473X C CAPACITOR 0.047uF 16V K R550 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J C637 NCB31CK-473X C CAPACITOR 0.047uF 16V K R551...
Page 89
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local R684 NRSA63J-822X MG RESISTOR 8.2kΩ 1/16W J R685 NRSA63J-682X MG RESISTOR 6.8kΩ 1/16W J R686 NRSA63J-123X MG RESISTOR 12kΩ 1/16W J R687 NRSA63J-682X MG RESISTOR 6.8kΩ...