Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for BARO BRC-4000
- Page 1 BARO SNT PRODUCT MANUAL BRC-4000 VER.1.0 2015/05/12 www.barosnt.com...
-
Page 2: Table Of Contents
CONTENTS Before Use: Cautions and Warnings……………………………………………………… 3 Component Descriptions: Front Panel Description……………..………………………………………. 4 Rear Panel Description……………………………………………………… 5 Control Pad Description: Home Screen Description………..…………………………………………. 7 Projector & Motor Control Screen Description…………………………..8 Motor Control Screen Description………………………………………….. 8 E.Q. Control Screen Description………….………………………………... 9 Lamp Control Screen Description………………………………………….. -
Page 3: Before Use
• If liquid has entered the product, be sure to disconnect it from all power sources, inputs and outputs, and contact your Baro representative for product inspection. • Only use the power cable and components that were originally supplied with the product. -
Page 4: Front Panel Description
CONTROLLER LAYOUT Rear Panel Description Infrared Control Outputs. Used to IR1 – Output for IR control of connected device. control connected devices with IR IR1 / IR2 IR2 – Additional output for IR control of connected device. control inputs. USB Ports for connection of Tablet Monitor touch functionality. -
Page 5: Rear Panel Description
18. NOTE IN interface. NOTE: The controller’s layout is designed according to use in Baro Digital Podiums. The inputs and outputs can be programmed to different functions if customization is required. Contact us or your product representative for more information. - Page 6 Front Panel Description Up – System powered ON Physical switch for controller power. Power Down – System off. Infrared receiver for programming IR Learn more about IR signal programming on page ???????. IR Sensor signals into the controller. The red LED light shows the status of the controller’s power and programming Power Status Indicator status.
-
Page 7: Home Screen Description
7” Pad Home Screen Description: LECTURE START – Automatically powers on projector, lowers projector and projector screen. Lecture Start / End LECTURE END – Automatically turns off projector, raises projector and projector screen. Select between operating the podium using the dedicated computer, or the device connected to the Notebook Input Source Interface. -
Page 8: Projector & Motor Control Screen Description
Projector & Motor Control Screen Description: Turn projector power on or off. Power On / Off Select between using the podium’s computer as the video input source, or using another AV device. Input Source Controls to blank the projector video output. This does not turn off the projector, but stops it from transmitting Mute (blank) any images while mute is in effect. -
Page 9: E.q. Control Screen Description
E.Q. Control Screen Description: Reset all custom volume settings to their factory presets. Volume Reset HIGHT / LOW – Control tonal settings for Mic1’s output. Mic 1 HIGH / LOW – Control tonal settings for the system’s overall audio output. Audio HIGH / LOW –... -
Page 10: Lamp Control Screen Description
Lamp Control Screen Description: Pressing this button will turn On all lighting controlled by the system. All On Pressing this button will turn Off all lighting controlled by the system. All Off Initiates Lighting System’s power saving mode. Power-Saving Control the On/Off status of each light individually. Light 1~12 Return to the main screen. -
Page 11: Connection
CONNECTION PC, and Laptop Interface: The following connection map is based on installation in a Baro Digital Podium. www.barosnt.com... -
Page 12: Monitor, 7" Pad, Projector, Microphones
Tablet Monitor, 7” Pad, and Microphones: The following connection map is based on installation in a Baro Digital Podium. www.barosnt.com... -
Page 13: Screen/Projector Elevation, Auxiliary
Screen/Projector Elevation, Auxiliary: SCREEN ELEVATION PROJECTOR ELEVATION POWER DOWN DOWN 220V 220V AUX 1 AUX 2 Speakers: LEFT RIGHT www.barosnt.com... -
Page 14: Controller - Projector Rs-232 Cable Connection
*** When connecting the Controller to a Projector, Controller RX No.3 and Projector RX No.3 are unused and should be terminated. This is common for most projectors, but when required by specific projectors (Panasonic, BenQ) No.3 may be used. BRC-4000 Video Controller... -
Page 15: Basic Projector Protocol Input
BASIC PROJECTOR PROTOCOL INPUT To connect your controller and projector, you must update the protocol. The following steps outline a basic protocol input method using only 7” touch pad. If this method is unsucessful, you will need to attempt the method found on page 16. In the projector and motor screen, press the top left corner. -
Page 16: Projector Protocol Input Procedure
PROJECTOR PROTOCOL INPUT PROCEDURE You will need to use a Windows based computer to conduct these changes. On the back of the controller, disconnect the KEYPAD RS-232 cable. Connect this port to the computer you will use to upgrade the protocol using an RS-232 cable. ***Before conducting protocol input, you should prepare your computer: Install vbruntimes.exe. - Page 17 Select the projector brand. Click the “Power On” button and every other function button once. Clicking these buttons commits the protocol changes in the controller. You should hear a beep emitted after each button is clicked. Once you have clicked and set each function button, you may repeat the process for Projector 2 if there is one connected.
-
Page 18: Controller Firmware Upgrade Procedure
CONTROLLER FIRMWARE UPGRADE PROCEDURE You will need to use a Windows based computer to conduct these changes. On the back of the controller, disconnect the KEYPAD RS-232 cable. Connect this port to the computer you will use to upgrade the protocol using an RS-232 cable. ***Before conducting protocol input, you should prepare your computer: Ensure the controller is powered off. -
Page 19: 7" Pad Upgrade Procedure
7” PAD UPGRADE PROCEDURE You will need to use a Windows based computer to conduct these changes. On the back of the controller, disconnect the KEYPAD RS-232 cable. Connect this port to the computer you will use to upgrade the protocol using an RS-232 cable. Remove the 7”... -
Page 20: Infrared Signal Programming
INFRARED SIGNAL PROGRAMMING ***By default the BRC-4000 controller is formatted to operate projector power (ON/OFF), input selection, and mute functions only. If you would like to control another device such as an interactive display or dvd player, the controller will require an update so that the proper functions and interface can be utilized in the 7”... - Page 21 Using the projector (or corresponding device’s) remote control, press the Power On button while aiming the remote control’s IR emitter at the BRC-4000’s IR receiver. Once accepted by the controller, the LED will blank for a moment and a beep will be emitted.
-
Page 22: Factory Settings
Looking at the top cover of your BRC-4000 you will see 2 holes. One is for adjustment of the BRC-4000’s amplifier IC chip volume output level. The other is a button for performing a factory reset. - Page 23 Factory Reset: Gently place a PH0 screwdriver or other narrow driver onto the head of the Factory rest button. Press firmly on the button. The reset is completed. It may be necessary to install firmware updates after completing a reset. www.barosnt.com...
-
Page 24: Full Specifications
FULL SPECIFICATIONS Controller Specifications (BR-4000): VGA X 2 VGA Input VGA X 2 VGA Output VGA, SVGA, XGA, QXGA Signal Type 2048 X 1536 Max. Resolution 440Mhz Pixel Frequency 3.5 Stereo X 2 Audio Input 55 Type X 2 Mic Input Audio L/R X 1 Audio Output Terminal Block Mini Type / MAX... - Page 25 Headquarters : 907-ho, 30 Songdomirae-ro, Smart Valley, Yeonsu-gu, Incheon, S. Korea 405-840 Online : http//www.barosnt.com | Office : +82-32-575-8589 | Fax : +82-32-575-8589 | Email : seunggi@barosnt.com...