free hit counter
Sony CFD-E95 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. CD Player
  5. CFD-E95 - Cd Radio Cassette-corder
  6. Service manual

Sony CFD-E95 Service Manual

Sony cd radio cassette-corder service manual
Hide thumbs Also See for CFD-E95:
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
Ver. 1.3 2005.09
AUDIO POWER SPECIFICATIONS
(US model only)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION
With 4-ohm loads, both channels driven from
100 - 10 000 Hz; rated 1.5 W per channel-
minimum RMS power, with no more than 10 %
total harmonic distortion in AC operation.
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of about
200 mm from the objective lens surface on the optical
pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20 000 Hz
Wow and flutter
Below measurable limit
Radio section
Frequency range
FM: 87.5 - 108 MHz
AM: 531 - 1 611 kHz (9 kHz step)
530 - 1 710 kHz (10 kHz step)
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
Sony Corporation
9-877-061-04
2005I05-1
Personal Audio Group
© 2005.09
Published by Sony Engineering Corporation
Model Name Using Similar Mechanism
CD
Optical Pick-up Block Name
Section
Optical Pick-up Name
Model Name Using Similar Mechanism
TAPE
Section
Tape Transport Mechanism Type

SPECIFICATIONS

Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 110 sec. with Sony cassette C-60
Frequency response
TYPE I (normal): 50 - 15 000 Hz
General
Speaker
in.) dia., 4 Ω, cone type (2)
Full range: 8 cm (3
1
⁄
4
Outputs
Headphones jack (stereo minijack)
For 16 - 68 Ω impedance headphones
Power output
1.8 W + 1.8 W (at 4 Ω, 10 % harmonic distortion)
Power requirements
For CD radio cassette-corder
Except Singapore, Korean, Australian models:
120 V AC, 60 Hz
Korean model: 220 V AC, 60 Hz
Singapore, Australian models: 230 V AC, 50 Hz
9 V DC, 6 size C (R14) batteries
For memory back-up:
4.5 V DC, 3 size AA (R6) batteries
For remote control:
3 V DC, 2 size AAA (R03) batteries
Power consumption
AC 14 W
CD RADIO CASSETTE-CORDER
CFD-E95
US Model
Canadian Model
E Model
Australian Model
CFD-E75
KSM-213RDP or KSM-213CDP
KSS-213R or KSS-213C
NEW
MF-E95
Battery life
For CD radio cassette-corder:
FM recording
Sony R14P: approx. 13.5 h
Sony alkaline LR14: approx. 20 h
Tape playback
Sony R14P: approx. 7.5 h
Sony alkaline LR14: approx. 15 h
CD playback
Sony R14P: approx. 2.5 h
Sony alkaline LR14: approx. 7 h
Dimensions
Approx. 272 × 164 × 285 mm (w/h/d)
× 6
× 11
(10
3
⁄
1
⁄
1
⁄
inches) (incl. projecting parts)
4
2
4
Mass
Approx. 3 kg (6 lb. 10 oz) (incl. batteries)
Supplied accessories
AC power cord (1)
Remote control (1)
Design and specifications are subject to change without
notice.

Advertisement

Table of Contents
loading

Related Manuals for Sony CFD-E95

Summary of Contents for Sony CFD-E95

  • Page 1: Specifications

    POWER OUTPUT AND TOTAL HARMONIC Fast winding time DISTORTION Sony R14P: approx. 13.5 h Approx. 110 sec. with Sony cassette C-60 With 4-ohm loads, both channels driven from Frequency response Sony alkaline LR14: approx. 20 h TYPE I (normal): 50 - 15 000 Hz 100 - 10 000 Hz;...

  • Page 2: Table Of Contents

    CFD-E95 TABLE OF CONTENTS SERVICING NOTES ..........GENERAL ..............DISASSEMBLY 3-1. Disassembly Flow ............9 3-2. Cabinet Upper Assy ............9 3-3. POWER Board ..............10 3-4. TUNER Board ..............10 3-5. MAIN Board ..............11 3-6. CD Mechanism Deck (KSM-213RDP) ......11 3-7.
  • Page 3 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

  • Page 4: Servicing Notes

    CFD-E95 SECTION 1 SERVICING NOTES CHUCK PLATE JIG ON REPAIRING NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT On repairing CD section, playing a disc without the CD lid, use Chuck Plate Jig. The laser diode in the optical pick-up block may suffer electro- •...
  • Page 5 Korean model: AC: 220 V 60 Hz 14 W *E92: Central and South America model The CFD-E95 is available with four types and seven defferent color variations. How to identify the destination, type, and color variation is shown below. – CD LID Top View –...

  • Page 6: General

    CFD-E95 SECTION 2 This section is extracted from instruction manual. GENERAL Basic Operations Playing a CD Use these buttons for additional operations 1, 2 ZPUSH OPEN/CLOSE VOLUME +, — Jog dial POWER Do this adjust the volume Press VOLUME +*, — (VOL +, —...

  • Page 7: Playing A Tape

    CFD-E95 Playing a tape Use these buttons for additional operations POWER VOLUME +, — m, M Press adjust the volume VOLUME +*, — (VOL +, — on the remote) stop playback Connect the supplied AC power cord. m or M...

  • Page 8: Setting The Clock

    CFD-E95 The Timer Setting the clock Press ENTER. The clock starts from 00 seconds. — —:— — indication appears in the display until you set the clock. CLOCK/SLEEP/TIMER The time display system: 12-hour system AM 12:00 = midnight ENTER Jog dial...

  • Page 9: Disassembly

    CFD-E95 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-2. CABINET UPPER ASSY (page 9) 3-3. POWER 3-4. TUNER 3-8. CABINET 3-12. CD LID 3-5. MAIN BOARD BOARD BOARD FRONT SECTION...

  • Page 10: Power Board

    CFD-E95 3-3. POWER BOARD 2 two screws 1 connector (2.6 × 10) (CNP901) 5 power board 4 connector (CNP322) 3-4. TUNER BOARD 5 screw (2.6 × 8) 2 three screws (2.6 × 10) 3 screw (2.6 × 10) 1 connector...

  • Page 11: Main Board

    CFD-E95 3-5. MAIN BOARD 1 flexible flat cable (CNP804) 1 flexible flat cable (CNP310) 3 four screws 1 flexible flat cable (2.6 × 8) (CNP802) 3 main board 1 flexible flat cable (CNP801) 1 flexible flat cable (CNP803) 2 connector...

  • Page 12: Optical Pick-Up (Kss-213R)

    CFD-E95 3-7. OPTICAL PICK-UP (KSS-213R) 1 two claws 3 CD cover 9 optical pick-up (KSS-213R) 2 two claws 7 flexible flat cable (16 core) 5 two screws (M2) 8 sled shaft 4 gear (A) 3-8. CABINET FRONT SECTION 1 four screws (2.6 ×...

  • Page 13: Tape Mechanism Deck (Mf-E95)

    CFD-E95 3-9. TAPE MECHANISM DECK (MF-E95) 0 three buttons (MD) (FWD, play, REC) 9 three buttons (MD) (pause, stop/eject, REW) 6 panel section qa tape mechanism deck (MF-E95) 3 two screws (2.6) 4 two screws (2.6) 7 four screws (2.6 × 8) 1 Push the button (MD) (stop/eject).

  • Page 14: Main Belt (B), Sub Belt (B)

    CFD-E95 3-11. MAIN BELT (B), SUB BELT (B) 8 main belt (B) 7 motor block 6 screw (2.6 × 4.5) 9 sub belt (B) 5 screw (2.6 × 4.5) 1 screw (2 × 4) tape mechanism deck 2 harness 3 Remove four solders.

  • Page 15: Mechanical Adjustments

    CFD-E95 SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS PRECAUTION PRECAUTION 1. Clean the following parts with a denatured-alcohol-moistened 1. Setting swab : MEGABASS control : OFF record/playback head pinch roller erase head rubber belts TAPE DECK SECTION 0 dB=0.775 V...

  • Page 16: Tuner Section

    CFD-E95 0 dB=1 µV AM IF ADJUSTMENT TUNER SECTION Adjust for a maximum reading on level meter [AM] 450 kHz Setting: Function : RADIO ( ): Singapore, Taiwan, Korean, Australian model BAND button : AM AM VCO VOLTAGE ADJUSTMENT RELAY board...
  • Page 17 CFD-E95 Adjustment Location: – TUNER BOARD (Component Side) – T2 FM IF Adjustment AM VCO Voltage Adjustment T1 AM IF Adjustment FM VCO Voltage Adjustment FM Tracking Adjustment AM Tracking Adjustment – TUNER BOARD (Conductor Side) – (ANT) (VT) (GND) –...

  • Page 18: Cd Section

    CFD-E95 CD SECTION CD section adjustments are done automatically in this set. In case of operation check, confirm that focus bias. Focus Bias Check 1. Connect the oscilloscope to TP (RF) and TP (GND) on the CD board. 2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01) 3.

  • Page 19: Diagrams

    CFD-E95 SECTION 6 DIAGRAMS 6-1. BLOCK DIAGRAM – CD Section – OPTICAL PICK-UP BLOCK CD L-OUT LCHO INTERPOLATION (KSS-213R) SLICE ERROR MUTE DIGITAL FIN2 EFMIN (Page 21) LEVEL CORRECTION & FILTER CONTROL AUDIO CD ATTENUATION & RCHO R-CH DETECTOR DEEMPHASIS...

  • Page 20: Block Diagram - Tuner Section

    CFD-E95 6-2. BLOCK DIAGRAM – TUNER Section – FM IFT FM IF ANT1 FM TELESCOPIC ANTENNA FM/AM RF AMP, MIX, OSC, FM/AM IF AMP, DET, MPX L-OUT L-CH DET- MPX- TU L-OUT MIX-OUT IF-IN RF-IN FM IF RF AMP MUTE...

  • Page 21: Block Diagram - Main Section

    CFD-E95 6-3. BLOCK DIAGRAM – MAIN Section – REC/PB PRE AMP CD L-OUT IC301 VREF (Page 19) POWER MIC IN MUTE IC304 L.CD R-CH ELECTRICAL VOLUME L.RAD MUTE IC302 STANDBY SWITCH R-CH L-OUT L-IN L OUT L IN L.LO J321...

  • Page 22: Block Diagram - Power Supply Section

    CFD-E95 6-4. BLOCK DIAGRAM – POWER SUPPLY Section – LIQUID CRYSTAL DISPLAY D402 LCD401 LED DRIVE (LCD BACKLIGHT) Q402 (GREEN) D403 LED DRIVE (LCD BACKLIGHT) Q403 (ORANGE) BL-GRN BL-ORG D404 LED DRIVE (LCD BACKLIGHT) BL-RED Q404 (RED) REMOTE AAAA CONTROL...

  • Page 23: Note For Printed Wiring Boards And Schematic Diagrams

    CFD-E95 Ver 1.2 6-5. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Circuit Boards Location (In addition to this, the necessary note is printed in each block) Note on Printed Wiring Boards: Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF •...

  • Page 24: Printed Wiring Board - Cd Section

    CFD-E95 6-6. PRINTED WIRING BOARD – CD Section – • See page 23 for Circuit Boards Location. : Uses unleaded solder. (US, Canadian, E, Mexican models) CD BOARD R715 R714 C727 JW703 JW705 C711 C709 C716 FB701 R723 C754 JC704...

  • Page 25: Schematic Diagram - Cd Section

    CFD-E95 6-7. SCHEMATIC DIAGRAM – CD Section – • • See page 36 for Waveforms. See page 36 for IC Block Diagrams. C726 1000p C725 1000p C724 C723 0.01 C722 C721 C720 S701 (LIMIT) C750 C746 C747 R724 C751 C742...

  • Page 26: Printed Wiring Board - Tuner Section

    CFD-E95 Ver 1.2 6-8. PRINTED WIRING BOARD – TUNER Section – • See page 23 for Circuit Boards Location. : Uses unleaded solder. (US, Canadian, E models) ANT1 TELESCOPIC (US. CND, E) ANTENNA JC12 (SP, TW, KR, AUS) (ANT) MAIN BOARD...

  • Page 27: Schematic Diagram - Tuner Section

    CFD-E95 Ver 1.2 6-9. SCHEMATIC DIAGRAM – TUNER Section – • • See page 36 for Waveform. See page 36 for IC Block Diagrams. AM FERRITE-ROD ANTENNA 220p (VT) KV1520NT 100p AM OSC 0.22 0.001 JC12 JC11 0.01 220k 100p 0.01...

  • Page 28: Printed Wiring Board - Tape Deck Section

    CFD-E95 6-10. PRINTED WIRING BOARD – TAPE DECK Section – 6-11. SCHEMATIC DIAGRAM – TAPE DECK Section – • See page 36 for Waveform. • See page 36 for IC Block Diagram. • :Uses unleaded solder. See page 23 for Circuit Boards Location.

  • Page 29: Printed Wiring Board - Main Section

    CFD-E95 6-12. PRINTED WIRING BOARDS – MAIN Section – • See page 23 for Circuit Boards Location. : Uses unleaded solder. (Page 24) (Page 26) (Page 26) CD BOARD TUNER BOARD TUNER BOARD POWER BOARD CNP702 CNP1 CNP1 CNJ311 (Page 34)

  • Page 30: Schematic Diagram - Main Section (1/2)

    CFD-E95 6-13. SCHEMATIC DIAGRAM – MAIN Section (1/2) – • See page 36 for IC Block Diagram. (1/2) C331 R145 R330 C332 1000 2.2k 0.01 R146 C134 220k C133 R126 C124 R143 0.022 100k R128 Q125 2SC4081-T106Q R125 R149 AF AMP 2.2k...

  • Page 31: Schematic Diagram - Main Section (2/2)

    CFD-E95 Ver 1.2 6-14. SCHEMATIC DIAGRAM – MAIN Section (2/2) – • See page 36 for Waveforms. (2/2) CNP801 LED-6V LED-6V BL-SLEEP BL-SLEEP RESET SIGNAL BL-GRN BL-GRN GENERATOR BL-ORG BL-ORG IC802 BD4727G-TR BL-RED BL-RED (Page 33) D-GND R842 R843 CNP802...

  • Page 32: Printed Wiring Boards - Panel Section

    CFD-E95 6-15. PRINTED WIRING BOARDS – PANEL Section – • See page 23 for Circuit Boards Location. : Uses unleaded solder. (Page 29) MAIN BOARD LCD BOARD CNP314 S403 R404 CLOCK/SLEEP/ R406 TIMER R425 D406 R424 R402 R407 S406 S405...

  • Page 33: Schematic Diagram - Panel Section

    CFD-E95 6-16. SCHEMATIC DIAGRAM – PANEL Section – Q409 DTA143ZUA LCD BACKLIGHT SLEEP R431 R429 R434 SWITCH D405 R430 KDS120-RTK R432 D402 D403 D404 SML-011EBTT86T SML-012YTT86R SML-012UTT86S (LCD BACKLIGHT) (LCD BACKLIGHT) (LCD BACKLIGHT) (GREEN) (ORANGE) (RED) R442 R443 R444 R436...

  • Page 34: Printed Wiring Boards - Power Section

    CFD-E95 Ver 1.2 6-17. PRINTED WIRING BOARDS – POWER Section – • See page 23 for Circuit Boards Location. : Uses unleaded solder. POWER BOARD RELAY BOARD HEADPHONE BOARD C129 CNJ311 JC301 C130 C230 CNP322 R333 (R-CH) J321 MAIN C128...

  • Page 35: Schematic Diagram - Power Section

    CFD-E95 Ver 1.2 6-18. SCHEMATIC DIAGRAM – POWER Section – R231 R131 4.7k 4.7k R232 C324 0.01 R132 J321 (PHONES) R324 2.2k POWER AMP IC304 D323 BA5417 1SS355TE-17 R323 KH324 C323 CNP324 C128 1000p C131 CNP325 C130 CNJ322 CNP322 C228...
  • Page 36 CFD-E95 • Waveforms • IC Block Diagrams – CD Board – – TUNER Board – – MAIN Board – – CD Board – 1 IC701 4 (RF) (CD Play mode) 5 IC2 w; (XOUT) ea IC801 ua (XT2) IC701 LC78646E-E...
  • Page 37 CFD-E95 IC702 BA5826FP-E2 SP– D.BUFF SL– D.BUFF LEVEL D.BUFF SHIFT D.BUFF SPIN LEVEL SHIFT SLIN THERMAL SHUT-DOWN MONITOR (SLIN) REG–B VREF REGO MUTE (FIN) DRIVER MUTE (TIN) LEVEL LEVEL SHIFT D.BUFF SHIFT D.BUFF F– T– D.BUFF D.BUFF OPOUT OPIN – TUNER Board –...

  • Page 38: Main Board

    CFD-E95 IC2 LC72137M-TLM XOUT REFERENCE DIVIDER AOUT PHASE 12BITS DETECTOR PROGRAMMABLE CHARGE DIVIDER PUMP UNLOCK DETECTOR POWER ON RESET SWALLOW COUNTER FMIN 1/16,1/17 4BITS UNIVERSAL COUNTER AMIN IFIN – TC Board – – MAIN Board – IC301 TA2068N IC302 PT2257-S...

  • Page 39: Ic Pin Function Description

    CFD-E95 6-19. IC PIN FUNCTION DESCRIPTION • MAIN BOARD IC801 µPD789478GC-A04-8BT (SYSTEM CONTROLLER) Pin No. Pin Name Description 1, 2 — Not used 3 to 5 VLC2 to VLC0 — Terminal for doubler circuit capacitor connection to develop liquid crystal display drive voltage...
  • Page 40 CFD-E95 Pin No. Pin Name Description Sub system clock input terminal (32.768 kHz) Sub system clock output terminal (32.768 kHz) — Power supply terminal (+3.3V) — Ground terminal Main system clock input terminal (4.19 MHz) Main system clock output terminal (4.19 MHz) System reset signal input “L”: reset...

  • Page 41: Exploded Views

    CFD-E95 Ver 1.2 SECTION 7 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service.

  • Page 42: Cabinet Front Section

    CFD-E95 Ver 1.2 7-2. CABINET FRONT SECTION MD block section panel section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-247-666-01 LID, CASSETTE (BLUE (PSYC)) X-3383-048-1 CABINET FRONT SUB ASSY (W) 3-247-666-11 LID, CASSETTE (WHITE (LIV))

  • Page 43: Panel Section

    CFD-E95 Ver 1.2 7-3. PANEL SECTION lcd board section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-247-656-01 BUTTON (CENTER) 3-247-668-01 DIAL, JOG (for BLUE/RED/YELLOW (PSYC), (DISPLAY. CLOCK/SLEEP/TIMER. ENTER) WHITE (LIV)) (for BLUE/RED/YELLOW (PSYC), WHITE (LIV))

  • Page 44: Lcd Board Section

    CFD-E95 Ver 1.1 7-4. LCD BOARD SECTION LCD401 not supplied board not supplied IC401 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-251-738-01 SHEET-DIFFUSION A-4541-214-A LED BOARD, COMPLETE 3-247-675-01 PLATE, LIGHT GUIDE * 157 A-3663-825-A LCD BOARD, COMPLETE...

  • Page 45: Md Block Section

    CFD-E95 Ver 1.2 7-5. MD BLOCK SECTION not supplied supplied MF-E95 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-247-658-11 BUTTON (MD) (FWD) (J) 3-247-659-01 BUTTON (MD) (PAUSE) (S) (for SILVER, BLUE (ORIGINAL), (for BLUE/RED/YELLOW (PSYC), WHITE (LIV))

  • Page 46: Cabinet Upper Section

    CFD-E95 Ver 1.2 7-6. CABINET UPPER SECTION S901 not supplied (headphone board) CD block section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-951-620-01 SCREW (2.6X8), +BVTP 3-250-720-61 CABINET (UPPER) (RED (PSYC: CND)) * 252 A-3347-999-A MAIN BOARD, COMPLETE...

  • Page 47: Cabinet Under Section

    CFD-E95 Ver 1.2 7-7. CABINET UNDER SECTION speaker box section J901 T901 F901 ANT1 CND, SP, TW, KR, AUS battery (2) board battery (3) board battery (1) board The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety.

  • Page 48: Speaker Box Section

    CFD-E95 7-8. SPEAKER BOX SECTION Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-247-672-01 BOX, SPEAKER 3-250-730-01 DUCT COVER R 4-951-620-01 SCREW (2.6X8), +BVTP 1-825-474-11 SPEAKER (8cm) (R) 3-250-729-01 DUCT COVER L 1-825-474-11 SPEAKER (8cm) (L)

  • Page 49: Cd Block Section

    CFD-E95 Ver 1.2 7-9. CD BLOCK SECTION KSM-213RDP not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-923-736-01 COVER, CD * 404 A-3683-956-A CD BOARD, COMPLETE (US, CND, E) 3-931-379-31 RUBBER, VIBRATION PROOF 3-931-379-21 RUBBER, VIBRATION PROOF...

  • Page 50: Optical Pick-Up Section (Ksm-213Rdp)

    CFD-E95 7-10. OPTICAL PICK-UP SECTION (KSM-213RDP) M702 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce...

  • Page 51: Tape Mechanism Deck Section (Mf-E95)

    CFD-E95 Ver 1.1 7-11. TAPE MECHANISM DECK SECTION (MF-E95) M901 not supplied HRP301 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-244-086-01 ARM, PINCH ROLLER 3-244-083-01 + SCREW BIND DT M2X6 3-244-079-01 BELT (B), SUB...

  • Page 52: Electrical Parts List

    CFD-E95 BATTERY (1) Ver 1.2 SECTION 8 ELECTRICAL PARTS LIST BATTERY (2) BATTERY (3) NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by parts list may be different from the parts speci- are seldom required for routine service.
  • Page 53 CFD-E95 Ver 1.1 HEADPHONE Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > HEADPHONE BOARD ***************** JC701 1-216-864-11 SHORT CHIP JC702 1-216-864-11 SHORT CHIP < JACK > JC703 1-216-864-11 SHORT CHIP JC704 1-216-821-11 METAL CHIP...
  • Page 54 CFD-E95 Ver 1.2 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > R406 1-216-825-11 METAL CHIP 2.2K 1/10W R407 1-216-821-11 METAL CHIP 1/10W R436 1-216-805-11 METAL CHIP 1/10W R408 1-216-825-11 METAL CHIP 2.2K...
  • Page 55 CFD-E95 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C819 1-162-927-11 CERAMIC CHIP 100PF Q225 8-729-905-34 TRANSISTOR 2SC4081T106Q C820 1-115-156-11 CERAMIC CHIP Q801 8-729-029-16 TRANSISTOR DTC144VUA-T106 C821 1-115-156-11 CERAMIC CHIP C822 1-126-176-11 ELECT 220uF Q805...
  • Page 56 CFD-E95 Ver 1.2 MAIN POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R819 1-216-825-11 METAL CHIP 2.2K 1/10W R878 1-216-833-11 METAL CHIP 1/10W R820 1-216-813-11 METAL CHIP 1/10W (US (LIV)) R879 1-216-833-11 METAL CHIP 1/10W...
  • Page 57 CFD-E95 Ver 1.2 POWER RELAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C323 1-126-795-11 ELECT 10uF < COIL > C324 1-162-974-11 CERAMIC CHIP 0.01uF C333 1-126-796-11 ELECT 22uF L910 1-414-142-61 INDUCTOR C901 1-162-995-11 CERAMIC CHIP...
  • Page 58 CFD-E95 Ver 1.2 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C102 1-104-665-11 ELECT 100uF R205 1-216-835-11 METAL CHIP 1/10W C103 1-165-176-11 CERAMIC CHIP 0.047uF R206 1-216-825-11 METAL CHIP 2.2K 1/10W C104 1-162-966-11 CERAMIC CHIP 0.0022uF 10%...
  • Page 59 CFD-E95 Ver 1.2 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-162-970-11 CERAMIC CHIP 0.01uF < SHORT > 1-162-919-11 CERAMIC CHIP 22PF 1-162-964-11 CERAMIC CHIP 0.001uF 1-216-864-11 SHORT CHIP 1-216-864-11 SHORT CHIP 1-162-970-11 CERAMIC CHIP 0.01uF...
  • Page 60 CFD-E95 Ver. 1.3 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < VIBRATOR > ACCESSORIES ************ 1-795-449-11 VIBRATOR, CRYSTAL (75kHz) 1-557-287-11 CORD, POWER (E, TW) ************************************************************ 1-575-131-11 CORD, POWER (SP) MISCELLANEOUS 1-696-819-11 CORD, POWER (AUS)
  • Page 61 CFD-E95 US Model Canadian Model SERVICE MANUAL E Model Australian Model Ver 1.2 2004.05 SUPPLEMENT-1 File this supplement with the service manual. Subject: Change of Optical Pick-up Block (KSM-213RDP→KSM-213CDP) (SPM-04041) Optical pick-up block is changed from KSM-213RDP to KSM-213CDP in the midway of production.
  • Page 62 CFD-E95 OPTICAL PICK-UP SECTION (KSM-213CDP) not supplied not supplied (M701 (SPINDLE)) M702 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité.
  • Page 63 CFD-E95 MEMO...

  • Page 64: Revision History

    CFD-E95 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2003.02...

Table of Contents