Advertisement
Quick Links
BLURB
Installation and User Guide
IN-C
™ H
-R
E
EILING
ALF
ECESSED
NCLOSURES
For the Vaddio™ ClearVIEW™, PowerVIEW™ and RoboSHOT™ HD PTZ Cameras
Part Number: 999-2225-050 for HD-Series Cameras
Part Number: 999-2225-150 for RoboSHOT Cameras
©2014 Vaddio - All Rights Reserved
IN-Ceiling Half-Recessed Enclosure for HD and RoboSHOT Cameras
Document Number 342-0177 Rev. E
●
●
Advertisement
Related Manuals for VADDIO HD-Series
Summary of Contents for VADDIO HD-Series
- Page 1 ™ H EILING ECESSED NCLOSURES For the Vaddio™ ClearVIEW™, PowerVIEW™ and RoboSHOT™ HD PTZ Cameras Part Number: 999-2225-050 for HD-Series Cameras Part Number: 999-2225-150 for RoboSHOT Cameras ©2014 Vaddio - All Rights Reserved IN-Ceiling Half-Recessed Enclosure for HD and RoboSHOT Cameras Document Number 342-0177 Rev.
- Page 2 Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.
-
Page 3: Technical Features
The IN-Ceiling Half-Recessed Enclosure has a built-in active IR receiver on the trim ring and IR emitter circuit board on the inside of the back box. The IR circuit ensures that the Vaddio IR Remote Commander operates with the camera, as well as the Vaddio IR Forwarding feature of the Quick-Connect SR and Quick-Connect DVI/HDMI Interface systems. - Page 4 Step 1: For the most obvious reasons, a ladder is required to install the IN-Ceiling Half-Recessed Enclosure and Vaddio PTZ camera into an acoustic tile ceiling. Safety comes first, so please use safe tools ladders and installation practices. Choose the tile that the enclosure and camera are to be installed. Make sure that it is not too close to a wall or ceiling lighting fixture that will serve to interfere with proper operation of the camera lens or iris.
- Page 5 Step 4: Using the Quick-Connect SR, Quick-Connect DVI/HDMI-SR, Quick-Connect USB or Quick-Connect USB Mini Interfaces and the HD-Series or RoboSHOT Cameras: Two (2) Cat-5e cables are required for the cameras to operate with either the Quick-Connect SR Interface or the Quick-Connect DVI/HDMI SR Interface.
- Page 6 IN-Ceiling Half-Recessed Enclosure for HD Series and RoboSHOT Cameras Spacer Block for HD-20 Camera: HD-20 /20/22/30/USB When using the 999-2225-050 kit and the HD-20 /20/22/30/USB Spacer Block PTZ cameras, use the camera platform spacer to boost the height of the camera through the enclosure collar ring as shown on right. These cameras are approximately ¾”...
-
Page 7: Warranty Information
Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under warranty. If the product is out of warranty, Vaddio will test then repair the product or products. The cost of parts and labor charge will be estimated by a technician and confirmed by the customer prior to repair. - Page 8 ©2015 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, ClearVIEW, PowerVIEW, EZCamera, WallVIEW, RoboSHOT, Quick-Connect and IN-Ceiling are trademarks of Vaddio. All other trademarks are property of their respective owners.