Advertisement
Quick Links
Advertisement
Summary of Contents for Zhongshan Hongmao SM-800D
- Page 1 TWO-WAY LCD VEHICLE SECURITY SYSTEM OPERATION & INSTALLATION INSTRUCTIONS...
-
Page 2: Technical Specification
TECHNICAL SPECIFICATION 1. Main Control Module Working Voltage : 9V-15VDC Stand by Current Consumption: 20 mA Active Current Consumption: 500 mA - 2A Working Temperature Range: -40 ~ +70 Frequency Range: 433.92MHz + 75KHz TX Range: 600-800m Working Mode: ASK 2. - Page 3 QUICK REFERENCE ON USE OF REMOTE CONTROL Button 1.1 Alarm disarmed: Press button once, the central door lock will lock, the ignition and the trunk will arm in 3 seconds, and the doors will arm automatically after the dome light is turned off, the sensor will be activated in 25 seconds to ensure the lifting operation of the power window is completed.
- Page 4 QUICK REFERENCE ON USE OF REMOTE CONTROL Button 4.1 Press & release button , the LED of the Remote Control will illuminate for 1 second (Press button once when the alarm is triggered , the LED will illuminate for 4 seconds.) 4.2 While the alarm is disarmed, open a vehicle door, turn the ignition to position, press &...
-
Page 5: Brief Look At Each Device
BRIEF LOOK AT EACH DEVICE 1.Main Control Module (for vehicle of negative polarity ground 12V constant power) It is a main part of the Vehicle Security System and it is usually installed in a hidden location under the bottom of the dashboard in the vehicle. Use the wiring diagram as a reference, connect the module wires to the vehicle's ignition, turn signal lights, constant power, etc respectively. - Page 6 BRIEF LOOK AT EACH DEVICE 4.Siren If installed, alarm sound of higher than 110 dB is set off from the siren when the vehicle is attacked. It should be mounted in a place to protect it from heat and water damage. 5.Remote Co ntrol The Remote Control mainly consists of ASK electronic circuits, LCD screen, melody buzzer and a vibrator (vibrator is optional).
- Page 7 POINTS TO BE NOTED FOR YOUR BETTER USE 1.About Tw o-Way Tr ansmission As the system is of two-way signal transmission, sometimes the time required for communication takes longer than usual when communicating remotely either to operate the system or to check the operation result since a large amount of information is to be exchanged between the TX part and RX part of the system with one press of button.
- Page 8 FEATURES ILLUSTRATION 1. Ar m Th e Ve hicle & Do or Lo ck Exit the vehicle and close all of the doors. Press button , the siren will chirp once, the turn signal lights will flash once, the doors will lock, the power window output will be activated, the Remote Control will emit a short chirp, the ignition and the trunk will arm in 3 seconds, the doors will arm automatically after the domelight is turned off, the sensor will be activated in 25 seconds and the LED...
- Page 9 FEATURES ILLUSTRATION 3. Disarm The Vehicle & Door Unlock A.Press button while the alarm is armed with sound and light, the siren will emit 2 chirps, the turn signal lights will flash twice, the central door lock will unlock,the LED will stop flashing, the system will disarm and the Remote Control will beep twice.
- Page 10 FEATURES ILLUSTRATION 6. System's Status Check By pressing button , you can check whether your Remote Control is within the range of transmission or not. If within the range, the Remote Control will beep 3 times. If you are out of range, the Remote Control will not emit any sound.
- Page 11 FEATURES ILLUSTRATION of time (either 8, 16, 24 or 60 minutes) then shut down and the system will enter armed state again. While the remote started engine is running, you may press button to shut it down, the Remote Control will beep twice and the system will enter armed state again.
- Page 12 FEATURES ILLUSTRATION Valet Switch for 5 seconds, the siren will chirp once to indicate the system is now in programming mode. While the system is in programming mode: a.Press the Override/Valet Switch once, the siren will chirp twice and indicate the 0.9-second crank time is selected.
- Page 13 FEATURES ILLUSTRATION 10. System features programming To enter the system features programming mode: While the system is disarmed, press & hold the brake pedal, press & hold the Override/Valet Switch for 3 seconds, the siren will chirp once to indicate the system has entered programming mode. A.
- Page 14 FEATURES ILLUSTRATION unit is disconnected then connected again, it will return the engine running time to the default setting 8 minutes. (Only system with remote engine start has this function.) After programming is complete, remove your foot from the brake pedal to exit programming mode. 11.
- Page 15 FEATURES ILLUSTRATION In case a Remote Control is lost you may go to the dealer near your location to buy a new one then memorize the codes of the Remote Control into the system. For security of your IMPORTANT! vehicle please erase the code of the lost Remote Control from memory thenlearn all the Remote Controls again and this will prevent the illegal user who obtainedthe lost Remote Control from using it to operate the alarm system.
- Page 16 FEATURES ILLUSTRATION To enable this function: Open the vehicle door while the alarm is disarmed, turn the ignition to position, press and hold button on the Remote Control for 3 seconds with a distance to the vehicle for 2 to 3 meters, the siren will emit a short chirp, the Remote Control will beep once, the icon will display on the LCD screen and the system is now in AUTO mode To disable this function: Open the vehicle door, turn the ignition to...
- Page 17 FEATURES ILLUSTRATION will flash 6 times and the LED will light solid to warn away potential intruders. The Remote Control will sound for 15 seconds and vibrate 5 times (Only Remote Control with vibrator has this function.). The LCD screen displays as picture (8). If any light impact is applied to the vehicle again within 15 seconds or the vehicle is impacted heavily for the first time, the siren will sound and the turn signal lights will flash for 25 seconds, the starter interrupt will engage, the LED will light solid, the Remote Control will sound for 15 seconds and vibrate 5 times...
- Page 18 FEATURES ILLUSTRATION 18. Vibration Mode Of The Remote Control (Optional) It is difficult to hear the beep sound of the Remote Control after the alarm is triggered while you are in a noisy place. In this occasion the vibration mode is helpful. And you may disable this function if you think it is not necessary or for power saving purpose.
- Page 19 FEATURES ILLUSTRATION The Override/Valet Switch should be installed in a hidden location IMPORTANT! where it is convenient to operate. B. Valet Mode This is for situation in which it is not convenient for the alarm to be armed, such as car wash. In the valet mode all of the alarm's security features have been turned and only the convenience features such as keyless entry can be operated.
- Page 20 FEATURES ILLUSTRATION 24. Features Selectable By Jumper Jumper Table (Factory setting: Vacuum Pump Type Central Lock Power Central Door Lock Engine Disable Engine Enable (Anti-Hijack Mode) Auto Arming ON Auto Arming OFF Door Trigger (-) Door Trigger (+) -19-...
- Page 21 CENTRAL DOOR LOCK INSTALLATION INSTRUCTION There are over 10 kinds of central door locks. Please follow the wiring diagrams to complete the installation of the central door lock systems. 1.Remove the door trim of the vehicle's door, find a mounting location for the Door Lock Actuator (Door Motor) near the manual door lock switch.
- Page 22 CENTRAL DOOR LOCK WIRING DIAGRAM Orange Orange +12V Orange OFF Signal White White White OFF Signal Yellow Yellow Yellow Orange/Black Orange/Black Orange/Black ON Signal White/Black White/Black ON Signal White/Black Yellow/Black Yellow/Black Yellow/Black Diagram 2. Negative Trigger Diagram 3. Positive Trigger Diagram 1.
- Page 23 WIRING DIAGRAM(FOR SYSTEM W/O ENGINE STARTER) -22-...
- Page 24 WIRING DIAGRAM(FOR SYSTEM W/ ENGINE STARTER) -23-...
-
Page 25: Tips For Troubleshooting
TIPS FOR TROUBLE SHOOTING PROBLEM SOLUTION After installation of the main control module, 1.Check whether the plug is inserted in opposite side. the siren sounds continuously and cannot be 2.Check whether the wire connections are correct. stopped by remote control. 3.Check whether the fuse is burnt. - Page 26 TIPS FOR TROUBLE SHOOTING PROBLEM SOLUTION 1.Check whether the battery of the Remote Control is low. 2.Check whether the Remote Control is soaked. 3.Check whether the Remote Control is broken. To find out whether the Remote Control used has the Remote Control does not work.