Website:http://biz.LGservice.com E-mail:http://www.LGEservice.com/techsup.html COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CA-126 FACTORY MODEL: CR575H MODEL: StudioWorks 585E (CR575H-EL) ) ID LABEL Model No. CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. *Same looking with new chassis. Issue Date; 2003. 02.
SAFETY PRECAUTIONS SAFETY-RELATED COMPONENT WARNING! X-RADIATION There are special components used in this color monitor The only potential source of X-radiation is the picture tube. which are important for safety. These parts are marked However, when the high voltage circuitry is operating on the schematic diagram and the replacement properly there is no possibility of an X-radiation problem.
TIMING CHART VIDEO SYNC << Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >> Sync Total Period Video Active Sync Duration Back Porch Blanking Time Front Porch Mode Resolution Frequency Time (A) Sort Polarity –...
OPERATING INSTRUCTIONS FRONT VIEW REAR VIEW See Front Control Panel Power ON/OFF Button AC Power Socket Signal Connector Front Control Panel 3. SET Button 1. Power ON/OFF Button This button to enter a selection in the on screen display. This button is used to turn the monitor ON and OFF. 4.
DESCRIPTION OF BLOCK DIAGRAM 1. Line Filter & Associated Circuit 7. D/D(DC to DC) Converter This is used for suppressing noise of power input line This circuit supplies DC voltage to the horizontal flowing into the monitor and/or some noise generated deflection output circuit by increasing DC 50V which is in the monitor flowing out through the power input line.
ADJUSTMENT GENERAL INFORMATION 7) Adjust parallelogram as arrow keys to be the best condition. All adjustment are thoroughly checked and corrected 8) Adjust balance of pin-balance as arrow keys to be when the monitor leaves the factory, but sometimes the best condition. several adjustments may be required.
Page 10
6. Adjustment for Focus. 17-1) Adjust R-DRIVE and B-DRIVE command to white 1) Set the Brightness and Contrast to max position. ± 0.003 and y=0.298 ± 0.003 on the balance x=0.283 2) Display H character in full screen at Mode 4. White Balance Meter with PC arrow keys.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK TROUBLE IN FUSE FUSE OK? (F901) (F901) CHECK C908 VOLTAGE? TROUBLE IN D900 (AC120V: 160VDC, AC220V: 304VDC) CHECK IC901 PIN 6 TROUBLE IN WAVEFORM (SQUARE WAVE IC901 COMES OUT?) CHECK TROUBLE IN D941, D942, D951,...
Page 12
2. NO CHARACTER NO CHARACTER CHECK TROUBLE IN IC302 P302 5V LINE PIN 7 (5V) ? TROUBLE IN CHECK PC SIGNAL, IC302 PIN 1, 3, 5 ? P301 SIGNAL CABLE CHECK TROUBLE IN IC302 PIN 14, 16, 18 ? IC302 CHECK TROUBLE IN IC303 PIN 7 (105V)
Page 13
3. NO RASTER NO VIDEO (POWER INDICATOR ON) CHECK ORANGE DPM MODE POWER INDICATOR (NO H and/or V SYNC) GREEN or ORANGE? GREEN CHECK TROUBLE IN D712 ANODE D712 (-157V)? CHECK TROUBLE IN G1 VOLTAGE? Q799 (-75 ~ -15V) CHECK TROUBLE IN CDT HEAT D941, Q942, Q941...
4. NO HORIZONTAL DEFLECTION NO H-DEFLECTION (ONE VERTICAL LINE) CHECK TROUBLE IN Q706? Q706 CHECK B + VOLTAGE TROUBLE IN 50V LINE (50V)? CHECK T701(FBT) PIN 2 TROUBLE IN (31KHZ, 65V Q719, Q720, D710 54KHZ, 120V ? CHECK TROUBLE IN Q701 COLLECTOR Q701 WAVEFORM?
Page 15
5. TROUBLE IN H-LINEARITY UNBALANCED OF H-LIN. CHECK TROUBLE IN IC401 IC401 (MICOM) PIN 5, 6? CHECK TROUBLE IN Q712, Q713 Q712, Q713, Q715, Q716 Q715, Q716? CHECK TROUBLE IN L703? L703 Cs SIGNAL TABLE HORIZONTAL FREQUENCY(fH) 30K ~ 33.9K TROUBLE IN 34K ~ 38.9K C722, C726, C729...
Page 16
6. NO VERTICAL DEFLECTION NO V-DEFLECTION (ONE HORIZONTAL LINE) CHECK TROUBLE IN IC601 PIN 2 13V LINE (13V)? CHECK TROUBLE IN IC601 PIN 4 -10V LINE (-10V)? CHECK TROUBLE IN IC701 PIN 5, 23? IC701 TROUBLE IN IC601, V-CIRCUIT - 16 -...
Page 17
7. TROUBLE IN OSD (ENTER BUTTON MUST BE PRESSED.) NO OSD CHECK TROUBLE IN IC301 B + ? 5V LINE DC 5V CHECK TROUBLE IN IC301 PIN 5, 10 IC601 PIN8 (V-FBP), WAVEFORM? T701 40V LINE (H-FBP) Pin 10 Pin 5 CHECK TROUBLE IN IC301 PIN 12...
Page 18
8. TROUBLE IN DPM (NO OFF MODE.) OFF MODE FAILURE CHECK CHECK PC, IC401 (MICOM) INPUT H/V SYNC SIGNAL (PC IS NOT GOING INTO PIN 30, 31 (H/V INPUT) DPM OFF MODE) SIGNAL? NO H/V SYNC CHECK TROUBLE IN IC401 PIN 13 X401 WAVEFORM? 24MHz...
Page 19
9. NO DEGAUSSING NO DEGAUSSING (DEGAUSS ON THE OSD MENU MUST BE PRESSED.) CHECK TROUBLE IN IC401 PIN 1 IC401 (MICOM) (0V)? CHECK TROUBLE IN Q953 COLLECTOR Q953 VOLTAGE? DC 13V CHECK TROUBLE IN P902 ? P902 CHECK TROUBLE IN RL901? RL901 TROUBLE IN...
Page 20
10. NO TILT (NO ROTATION ) NO TILT (NO ROTATION) CHECK TROUBLE IN IC401 PIN 21 IC401 ( MI COM) WAVE FORM ? CHECK TROUBLE IN 15V LINE 15V LINE, 6.3V LINE AND 6.3V LINE ? CHECK TROUBLE IN Q503 EMITTER Q501~Q503 VOLTAGE ? TROUBLE IN...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2003. 02. 19. DATE: 2003. 02. 19. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.
SCHEMATIC DIAGRAM NOTICE Since this is a basic schematic diagram. The value of components and some partial connection are sucject to be changed for improvement without notice. - 30 - - 31 -...