CONTENTS SAFETY PRECAUTIONS................................2 SERVICE HINTS ..................................3 SERVICE POSITION.................................4 ADJUSTMENT PROCEDURE AND FACTORY SETTINGS .....................5 WAVEFORM PATTERN TABLE ...............................6 ALIGNMENT SETTINGS................................7 BLOCK DIAGRAMS ..................................8 PARTS LOCATION .................................12 REPLACEMENT PARTS LIST ..............................13 SCHEMATIC DIAGRAMS ...............................22 CONDUCTOR VIEWS................................26 SAFETY PRECAUTIONS GENERAL GUIDE LINES It is advisable to insert an isolation transformer in the Check each exposed metallic part and check the a.c.
SERVICE HINTS How to remove the rear cover Remove the 10 screws as shown in Fig.2. SCREWS Fig.2. LOCATION OF CONTROLS P - Board Focus M - Board Screen H - Board E - Board Y - Board Fig.3.
HOW TO MOVE THE CHASSIS INTO SERVICE POSITION Remove the bead clamper from the mains lead and screw, using back cover screw, into top right-hand cabinet rib (A), shown in Fig.4. Hold and lift the rear of the E-PCB chassis and gently pull the chassis toward you, as shown in Fig.4. Release the respective wiring clips and rotate the chassis vertically through 90°, anti-clockwise.
ADJUSTMENT PROCEDURE Item / Preparation Adjustments Set the +B voltage up as follows:- +B SET-UP Adjust R811 so that B2 shows 148V±1V. Receive a Greyscale signal. Confirm the following voltages. Set the controls :- ± 0,25V ± 0,25V Brightness Minimum 12 ±...
WAVEFORM PATTERN TABLE Vert Drive Vert Out VFLB IC451 Pin 2 IC601 Pin 31 IC451 Pin 3 20ms 20ms 20ms H - Out H - Out H - Pulse IC601 Pin 50 IC701 Pin 5 Base Q503 64µs 64µs 64µs HFLB HFLB Video Out...
ALIGNMENT SETTINGS (The figures below are nominal and used for representative purposes only.) Alignment Function Settings / Special features H-Pos Horizontal Position Optimum setting. V-Pos Vertical Position Optimum setting. H-Amp Horizontal Amplitude Optimum setting. V-Amp Vert. Amplitude Optimum setting. E/W-Amp1 EW-amplitude Optimum setting.
VIDEO BLOCK DIAGRAM Y - BOARD E - BOARD Q906 Q908 COILS Q905 Q907 Q909 IC601 61 V IN 1 Q950 Q951 TUNER Q104 IC351 SVM OUT 34 VIDEO PROCESSOR B OUT 39 Q353 Q305 Q306 43 B IN Q105 OUTPUT 42 G IN G OUT 38...
Page 18
Cct Ref Parts Number Description Cct Ref Parts Number Description R1255 ERJ6GEYJ912 S.M.CARB 0.1W R3202 ERDS1TJ151 CARBON 0.5W R1900 ERQ12HJ150 FUSIBLE 0.1W R3203 ERDS1TJ151 CARBON 0.5W R1901 ERJ6GEYJ273 S.M.CARB 0.1W R3204 ERG2FJ221 METAL R1902 ERJ6GEYJ472 S.M.CARB 0.1W R3205 ERG2FJ221 METAL R1903 ERJ6GEYJ103 S.M.CARB...
Page 19
Cct Ref Parts Number Description Cct Ref Parts Number Description 22pF 680nF C124 ECUV1H220JCX S.M. CAP C582 ECWF2H684J FILM 500V 10pF 8.2nF C125 ECUV1H100DCX S.M. CAP C583 ECWH15H822JN FILM 1500V 22µF 6.8µF C251 ECA1HM220GB ELECT C584 TAC4R6T682JC CERAMIC 400V 10nF 100nF C252 ECUV1H103KBX...
Page 20
Cct Ref Parts Number Description Cct Ref Parts Number Description 470pF C855 ECKC2H471J CERAMIC 500V C2104 ECUV1H102JCX S.M. CAP 470pF C856 ECA1AHG222B ELECT C2105 ECUV1H102JCX S.M. CAP 470pF C857 ECKC2H471J CERAMIC 500V C2106 ECUV1H102JCX S.M. CAP 470pF C858 ECEA1HGE102 ELECT C2107 ECUV1H102JCX S.M.
Page 21
Cct Ref Parts Number Description Cct Ref Parts Number Description 100nF C3101 ECUV1H104KBX S.M. CAP 100nF C3102 ECUV1E104KBX S.M. CAP 390pF C3111 ECUV1H391JCX S.M. CAP 270pF C3112 ECUV1H271JCX S.M. CAP 10nF C3201 ECUV1H103KBX S.M. CAP 10nF C3202 ECUV1H103KBX S.M. CAP 560pF C3203 ECUV1H561JCX...
SCHEMATIC DIAGRAMS FOR MODEL TX-W32R4 (EURO-4 CHASSIS) IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturer's specified parts. NOTE RESISTOR All resistors are carbon ¼W resistor, unless marked otherwise.