Website:http://biz.LGservice.com E-mail:http://www.LGEservice.com/techsup.html COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CL-70 MODEL: L3200A (L3200AC.AL**A) L3200A (L3200ATC.AL**A) L3200A (L3200AFC.AL**A) L3200A (L3200AKC.AL**A) ) **Same model for Service CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this 9. Use with this receiver only the test fixtures specified in service manual and its supplements and addenda, read this service manual. and follow the SAFETY PRECAUTIONS on page 3 of this CAUTION: Do not connect the test fixture ground strap publication.
Page 5
General Soldering Guidelines Replacement 1. Use a grounded-tip, low-wattage soldering iron and 1. Carefully insert the replacement IC in the circuit board. appropriate tip size and shape that will maintain tip 2. Carefully bend each IC lead against the circuit foil pad and solder it.
Page 6
Circuit Board Foil Repair At Other Connections Excessive heat applied to the copper foil of any printed Use the following technique to repair the defective copper circuit board will weaken the adhesive that bonds the foil pattern at connections other than IC Pins. This technique to the circuit board causing the foil to separate from or involves the installation of a jumper wire on the "lift-off"...
TIMING CHART VIDEO SYNC << Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >> 1) PC Mode Total Video Front Sync Back Sync Period Active Porch Duration Porch MODE H / V Frequency Resolution Polarity Clock...
Page 8
2) Component Video Mode(Y/Pb/Pr) Total Video Front Back Sync Sync Period Active Porch Duration Porch MODE H / V Frequency Resolution Polarity Clock ( E ) Time ( A ) ( C ) ( D ) ( F ) H(Pixels) 25.175 31.469 SDTV...
DESCRIPTION OF BLOCK DIAGRAM 1. Input Selection Circuit 6. De-interlacer 1) PC Input Selection This block is composed of MDIN150(U901) and This block is composed of GM1501(U402) and peripheral devices. peripheral devices. GM1501 (U402) controls this IC through IIC Line. And this IC converts 16 Bit Interlaced Y/UV signal to 2) Video Input Selection De-interlaced signal.
ADJUSTMENT All adjustment are thoroughly checked and corrected when the monitor leaves the factory, but sometimes several minor adjustment may be required. Adjustment should be following procedure and after warming up for a minimum of 30 minutes. • Alignment appliances and tools. - IBM compatible PC - Programmable Signal Generator.
Page 12
Windows EDID V1.0 User Manual 2. EDID Read & Write 1) Run WinEDID.exe Operating System: MS Windows 98, 2000, XP Port Setup: Windows 98 => Don’t need setup Windows 2000, XP => Need to Port Setup. This program is available to LCD Monitor only. 1.
SERVICE OSD SEREVICE MENU ■ Service Menu - Model : Model or Micom Version Model : L3200T V1.0 - Elapsed time : Time used for panel Elapsed Time : - Nvram Initial : EEPROM reset and use Default Data NVram Inatial - WB Adjust : Adjusts the white balance WB Adjust - Aging Mode : Sets the aging mode (User : OFF)
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK J601 VOLTAGE CHECK POWER BOARD (18V, 12V, 5V)? CHECK J602 VOLTAGE CHECK POWER BOARD (24V, 33V) ? CHECK X401 CHECK X401 (14.318MHz) ? CHECK CHECK MICOM(U402) J601 SUB POWER PORT(R634) (SUB POWER) ? CHECK KEY CONTROL BOARD...
Page 16
2. NO RASTER(OSD IS NOT DISPLAYED) NO RASTER (OSD IS NOT DISPLAYED) CHECK THE PERIPHERAL CHECK U402? IC U402 CHECK CHECK THE PERIPHERAL LVDS OUTPUT J802 (J802)? CHECK CHECK U607 AND THE INVERTER POWER PERIPHERAL IC U607 (J606, J607) ? CHECK INVERTER - 16 -...
Page 17
3. NO RASTER ON VIDEO SIGNAL INPUT NO RASTER ON VIDEO SIGNAL POWER CHECK OF CXA2040(U201) : U204(9V) POWER CHECK OF UPD64011(U904) : U905(3.3V), U906(1.5V) POWER CHECK OF MDIN150(U901) : U907(3.3V), U908(2.5V) POWER CHECK OF GM1501(U402) CHECK CABLE OF VIDEO/COMPONENT NO INPUT SIGNAL CHECK THE PERIPHERAL CHECK UPD64011(U904)I/O SIGNAL...
Page 18
4. SOUND TROBLE SHOOTING NO SOUND OUTPUT POWER CHECK OF MSP3420G(U501) : U522(8V), L501(5V), L505(5V) POWER CHECK OF TPA3004(U502) : C564(18V) CHECK SOUND OF VCR,DVD,PC CHECK OF CONNECTION OF TUNER AND ANTENNA CHECK SOUND INPUT =>PC SOUND(J707) =>VIDEO, DVD, DTV SOUND (RED, WHITE OF J701, J702) CHECK THE PERIPHERAL IC OF NO INPUT SIGNAL...
Page 19
5. NO RASTER STATE ON ANALOG SIGNAL NO RASTER ON ANALOG SIGNAL POWER CHECK OF GM1501(U402) POWER CHECK OF LVDS OUTPUT: J802 CONNECTOR(J101) CHECK CHECK THE PERIPHERAL IC NO INPUT SIGNAL OF D-SUB(J101) CHECK ADC I/O SIGNAL IN GM1501(U402) NO OUTPUT SIGNAL CHECK THE PERIPHERAL IC NO INPUT SIGNAL OF GM1501(U402)
Page 20
6. NO RASTER STATE ON DIGITAL SIGNAL NO RASTER STATEON DIGITAL SIGNAL POWER CHECK OF GM1501(U402) POWER CHECK OF LVDS OUTPUT: J802 CONNECTOR(J102) CHECK NO INPUT SIGNAL CHECK GM1501(U402) I/O SIGNAL CHECK THE PERIPHERAL IC NO OUTPUT SIGNAL OF GM1501(U402) NO INPUT SIGNAL CHECK THE PERIPHERAL IC CHECK LVDS I/O SIGNAL...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2005. 05. 19. DATE: 2005. 05. 19. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.