Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Zadako Z1
- Page 1 Car alarm Z1 User´s manual Version 1.7...
-
Page 2: Table Of Contents
Remarks to device installation ................14 Diagnostics......................15 Signalization in diagnostic mode................15 * ZADAKO is registered trade mark of company Zadako limited. All rights reserved. * ZADAKO reserves right to change or improve any of its products described in this manual, without primer notice of client. -
Page 3: Car Alarm Z1
Car alarm Z1 The car alarm Z1 ( further Car alarm, or device ) belongs to new generation of modern car security. Thank to integrated GSM module you can control your vehicle with your mobile phone. Car alarm has a special built in sensor that triggers the alarm when the car moves or when it inclines. -
Page 4: Password
Device setup by mobile phone Setup (control) of device by mobile phone can be done by sending setup SMS message to the telephone number of SIM card inserted in Car alarm. Password Each SMS message sent to telephone number of SIM card inserted in device must begin with access password. -
Page 5: Setup Commands
recommended to change the password again after the installation, to keep your car and your personal information safe ! Example: To change factory default password „abcd“ to new password „aa22“, write following SMS message and send it to the telephone number of SIM card inserted in the device: abcd PWD=aa22... - Page 6 COMMAND MEANING PWD=[New [password] PWD=1234 └─┘ Change password to [new password] password] [value] defines sensibility (acceleration or vehicle inclination) that will trigger alarm. In general, the lower the value is, the SEN=[value] higher is the sensitivity. [password] SEN=7 └─┘ Allowed range: 3 to 100. Factory default value is 5.
-
Page 7: Finding Out Current Car Alarm Settings
abcd SEN=5 └─┘ Finding out current Car alarm settings To find out the current settings of Car alarm the question mark is used. The question mark is considered an independent command, therefore it must be separated by space. It does not change any setting. If you want to use it, you have to put it at the end of SMS message. -
Page 8: Setup Of Telephone Numbers
Setup of telephone numbers COMMAND MEANING USAGE T1=[telephone number] [password] └─┘ T1=+421903111111 T2=[telephone number] [password ] └─┘ [telephone number] determines to T2=+421903222222 which number Car alarm will call and send alarm SMS messages. T3=[telephone number] [ password] └─┘ It is possible to enter maximum 4 T3=+421903333333 cell phone numbers. -
Page 9: Setup Of Text Reports
Setup of text reports COMMAND MEANING USAGE [text string] is name of Car S0=[text string]# [password] S0= Car alarm Z1 # └─┘ alarm [text string] is description of S1=[text string]# alarm report from motion [password] S1=Vehicle stolen# └─┘... -
Page 10: Setup Of Control Method
S0=Car alarm Z1# S2=battery low# └─┘ └─┘ Texts S1, S3, S4, S5, S6, as well as other settings keep unchanged in this case. Setup of control method Arming and disarming Car alarm is possible in three ways: a) Control by ignition key (Set by command KEY) Turning on ignition key in ignition box to position 1 deactivates Car alarm (switches it off from arming). -
Page 11: Rfid Setup
Notice ! • To set method of arming and disarming, it is possible to use only one from allowed commands in one message KEY / RFID / RFIDN / ARM / DISARM . Example: To set the control method write and send SMS message: abcd └─┘... -
Page 12: Reporting Alarm Status
Reporting alarm status Alarm status can be triggered by following means: • internal detector of motion / inclination sensor of motion and inclination is a part of device, and in case of move or inclination detection it trigers alarm • external signal inputs •External signal inputs can be connected to door contacts, (circuit protection), to sensors of glass break, or to any other sensor. -
Page 13: Indication By Led Diode
When Car alarm gets to alarm status, it sends SMS messages to all numbers assigned to Car alarm. SMS messages contain name of Car alarm, type of incident, which triggered alarm, GPS coordinates and actual speed, text description of location (if available) and length of last passed journey. Subsequently the device will try to call to preset telephone numbers. -
Page 14: Automatic Control Of Car Battery
SMS to the telephone number of your device: abcd ?P Answer will be in form: Always If available If vehicle is moving If is in GPS coordinates database Car alarm Z1 MOVE 48^12.1234, (SW) 5.7 Triblavina 16^58.1234 km/h <quadratic> ^ <minutes>.<tenth of minute>... -
Page 15: Remarks To Device Installation
Remarks to device installation Before you insert SIM card into device, make sure that protection by PIN code is deactivated and that data services are activated on your SIM card. Device should not be installed in the area, where it would be exposed to high temperatures (for example under the first level of cockpit, which can be heated by sun). -
Page 16: Signalization In Diagnostic Mode
•Double beep sounds, that indicates entry to diagnostics mode. Together with that due to security reasons adequate alarm generates. (If you have telephone numbers for alarm reports preset, Car alarm will send SMS messages and will try to call). • During this mode will actual tests be cyclic indicated (reported) currently by diode flashing and buzzer beep according to table (see chapter Signalization in diagnostic mode). - Page 17 1. User´s manual describes functions of Car alarm. Your installation company will familiarize you with the way of use, and will answer your questions. If necessary, contact the manufacturer. Manufacturer ZADAKO, spol. s r.o., Veternicova 17, 841 05 Bratislava Tel.: +421 2 64531086, Fax: +421 2 64531084 www.zadako.sk...