Touch Screen Keypad (Aui) Enable; Keypad Programming Fields - Honeywell ADEMCO VISTA SERIES VISTA-21iP Installation And Setup Manual

Hide thumbs Also See for ADEMCO VISTA SERIES VISTA-21iP:

User manual (64 pages)

Programming manual (25 pages)

Quick manual (2 pages)

Table Of Contents

Table of Contents

Touch Screen Keypad (AUI) Enable

The system supports up to four touch screen style

keypads (e.g., Symphony Advanced User Interface

(AUI), and 6270 Touch Screen keypad.

NOTE: Use of touch screen devices does not affect the

number of standard keypads supported.

*189

AUI Device 1 - 4 Enable

(for TouchScreen Style Keypads)

For Touchscreen device usage

0 = disable

1 = partition 1

2 = partition 2

3 = partition 3 (common)

For Remote Services device usage

5 = part. 1 (auto-stay arm disabled)

6 = part. 2 (auto-stay arm disabled)

7 = part. 3 (common; auto-stay arm disabled)

Device Addresses:

Set AUI addresses as follows:

AUI 1 address = 1

AUI 2 address = 2

AUI 3 address = 5

AUI 4 address = 6

AUI Compatibility Note: To ensure proper AUI device

operation, use AUI devices with the following rev levels: 6270

series use version 1.0.9 or higher; 8132/8142 (Symphony)

series use version 1.1.175 or higher.

To enable a touchscreen keypad, enter the option

corresponding to each touchscreen's home partition.

Note for Remote Services Devices: If using the

Remote Services feature of the communication device,

select an option 5-7, depending on the partition the

Remote Services device is associated with (these options

automatically disable auto-stay arming when the

system is armed from the respective Remote Services

device). Refer to the communication device's installation

instructions for details on enabling the Remote Services

feature.

NOTE: If using Remote Services (IP/GSM feature), one

of the touch screen (AUI) addresses may be used for

enhanced Remote Services feature set, though a

physical touch screen is not installed. See ∗29 Menu

Mode section for enabling Remote Services.

Remote Services Device Address: Using an AUI

device address for Remote Services provides enhanced

remote services features, but an actual AUI device

cannot use the same address. If no AUI addresses are

available (all four AUIs are being used), Total Connect 2

cannot be used for remote services. However, Total

Connect 1 can be used by choosing an available standard

keypad address and using the appropriate keypad

address field *190 - *196 to select the Remote Services

operating partition (some remote access features will be

unavailable).

Keypad Programming Fields

To enable keypads:

1. Set desired address at keypad (refer to keypad's

instructions for setting the address).

2. Use data field program mode to enable keypad

addresses, assign a partition, enable sound options

in fields *190-*196 as shown in the table above.

3. If desired, use data field *198 to turn on the display

of the partition number.

4. Set the following keypad-related data fields as

required by the installation:

*21 Quick Arm Enable, *23 Forced Bypass, *84

Auto STAY Arm

5. If using touch screen devices (AUI), enable each unit

in field *189 and set appropriate AUI addresses.

NOTES:

1. Options for keypad 1, address 16 are set by the

factory and cannot be changed.

2. Each keypad must be assigned a unique address,

starting at address 16 (address 16 is reserved for

keypad 1, which is automatically set to partition 1

with all sounds enabled). Keypads programmed with

the same address will give unpredictable results.

3. If using Remote Services (IP/GSM feature), one of

the keypad addresses may be used for limited

Remote Services features, though a physical keypad

is not installed. See ∗29 Menu Mode section for

enabling Remote Services.

*190

Keypad 2 Device Address 17

Entry 1 – Partition Assignment:

For Touchscreen device usage

0 = disable

1 = partition 1

2 = part. 2

3 = part. 3 (common)

For Remote Services device usage

5 = part. 1 (auto-stay arm disabled)

6 = part. 2 (auto-stay arm disabled)

7 = part. 3 (common; auto-stay arm disabled)

Entry 2 – Sound Option:

0 = no suppression

1 = suppress arm/disarm and E/E/ beeps

2 = suppress chime beeps only

3 = suppress arm/disarm, E/E/ beeps and chime beeps

Entry 1: Enter the partition in which the keypad is

located.

Entry 2: Enter the desired sound option for this keypad