Summary of Contents for Rangemaster RM61000EX series
Page 1
RM61000EX Series ENGLISH........2 FRANÇAIS........13 ESPAÑOL........24 Broan-NuTone LLC. 926 West State Street, Hartford, WI 53027 NuTone, Inc., 4820 Red Bank Road, Cincinnati, OH 45227 Broan-NuTone Canada, INC.1140 Tristar Drive, Mississauga, Ontario, L5T 1H9...
Page 2
READ AND SAVE THESE INSTRUCTIONS INTENDED FOR DOMESTIC COOKING ONLY WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.
Page 3
CAUTION 1. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages. 2. Take care when using cleaning agents or detergents. 3.
EXTERIOR OR IN-LINE BLOWER SELECTION CAUTION: Either an exterior blower or in-line blower may be used with this hood. The RM61000EX hood must be installed with blower models 331H, 332H, 335, 336, HLB3, HLB6, HLB9 or HLB11 only. Other Blowers cannot be substituted (Blowers sold separately).
IN-LINE BLOWER INSTALL MOUNTING 48” MODEL FRAMING BEHIND DRYWALL BRACKETS 1. Construct wood wall framing that is flush with interior surface of wall studs.Make sure: a) the framing is centered over installation location. b) the height of the framing will allow the mounting brackets to be secured to the framing within the dimensions shown.
INSTALL THE HOOD RECTANGULAR MOUNTING SCREWS CUTOUTS (4,8x38mm) 1. Hang the hood from the brackets through the rectangular cut-outs on the back of MOUNTING the hood. Cut-outs are larger than the BRACKETS brackets to allow for horizontal adjustment. The bottom of the hood should be 24" to 30"...
Blower connection at hood: BLOWER CONNECTION AT HOOD 1. Run 2-wire plus ground power cable from the exterior or In-Line blower to the hood’s wiring box marked “motor connection”. Exterior or In-Line CONNECT: WHITE-TO-WHITE, blower 2. Remove the cover from the wiring box and RED-TO-BLACK, remove one knockout.
MAINTENANCE Proper maintenance of the Range Hood will assure proper performance of the unit. Grease Filters The grease filters should be cleaned fre- quently. Use a warm detergent solution. Grease filters are dishwasher safe. Remove filter by pushing filter towards the back of hood and rotating filter downward.
OPERATION BLOWER LIGHT ON / OFF SWITCH BLOWER Controls SWITCH SPEED The hood is operated using the slide controls CONTROL under the front edge of the hood. The light switch turns the halogen lights on and off. The blower on / off switch turns the blower on to the running speed set by the blower speed PILOT LAMP...
FUSE REPLACEMENT FUSE ELECTRICAL SWITCH OFF THE ELECTRICITY SUPPLY. SUPPORT Remove the grease filters. Remove the electrical box support and open the electrical box. Replace with the same type of fuse (5x20mm, 5A, 125V). ELECTRICAL - 11 -...
WARRANTY BROAN-NUTONE LLC ONE YEAR LIMITED WARRANTY Broan-NuTone LLC warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WAR- RANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
SERVICE PARTS MODEL RM61000EX - Parts for stainless steel models shown. For service parts for black, white, polished brass, or brushed copper models, call Broan Customer Service. KEY NO. PART NO. DESCRIPTION B08087135 Grease Filter (n.3) - 36” model B08087136 Grease Filter (n.
Page 14
SERVICE PARTS - LISTE PIECES DE RECHANGE - LISTA DE PIEZAS DE RECAMBIO MODEL 61000 EX - 39 -...