Installation Requirements; Tools And Parts; Location Requirements - KitchenAid KSSC36FTS Installation Manual
Architect series
overlay series
Hide thumbs
Also See for KSSC36FTS:
- Installation manual (80 pages) ,
- Energy manual (2 pages) ,
- Installation instructions manual (80 pages)
Table of Contents
Advertisement
Available languages
Available languages
INSTALLATION
Tools and Parts
IM PORTANT:
•
Installer: Leave Installation Instructions with the homeowner.
•
Homeowner:
Keep Installation Instructions for future
reference. Save these Installation Instructions for the local
electrical inspector's use.
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
•
Cordless drill
•
Drill bits
•
Adjustable
wrenches (2)
•
Phillips screwdriver
•
Small level
•
Appliance dolly
•
Torx®tT27 screwdriver
•
1V32" n ut driver
•
3/8"and 1/2"open-end wrenches
•
5/32"hex key
•
1/4"and %e" socket drivers
•
Tape measure
•
Utility knife
Parts Needed
•
#8 x 3" (7.6cm) wood screws (longerscrews may be needed)(6)
2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s) (1 or 2)
Order factory panels, make custom panels or consult a
qualified cabinetmaker
or carpenter to make the panels.
Classic Series: Order factory panels, make custom panels, or
consult a qualified cabinetmaker or carpenter to make the
panels. See "Classic Series Custom Panels" for more
information.
Overlay Series: Make custom panels, or consult a qualified
cabinetmaker
or carpenter to make the panels. See "Overlay
Series Custom Panels and Handle Kits" for more information.
Architect ®and Complete Series are shipped complete.
If you are connecting the water line directly to copper tubing
and not to a shutoff valve, you need a ferrule, a union, and a
1/4"(6.35 mm) compression fitting.
Locat
on Requ
rements
The refrigerator can be recessed in an opening between cabinets
or installed at the end of a cabinet run using a side panel to
enclose the refrigerator.
Explosion
Hazard
Keep flammable
materials
and vapors,
such as
gasoline,
away from refrigerator.
Failure to do so can result in death, explosion,
or fire.
REQUIREMENTS
It is recommended
that you do not install the refrigerator near
an oven, radiator, or other heat source.
Do not install in a location where the temperature will fall
below 55°F (13°C).
Floor must support the refrigerator weight, more than 600 Ibs
(272 kg), door panels and contents of the refrigerator.
Ceiling height must allow for side tipping radius. See "Tipping
Radius."
•
Location should permit door to open fully. See "Door Swing
Dimensions."
•
Location must permit top grille removal. See "Opening
Dimensions."
Opening Dimensions
To avoid tipping during use, the solid soffit must be within 1"
(2.5 cm) maximum above the refrigerator. If the solid soffit is
higher than 1" (2.5 cm) or one is not available, then the
refrigerator must be braced.
If anti-tip boards are needed, they must be installed to the rear
wall studs so that the bottom of the anti-tip board is 84"
(213.4 cm)from
the floor. See "Install Anti-Tip Boards" for
more information.
NOTES:
A clearance of 1/2"(1.3 cm) must be maintained above the
top grille in order for the top grille to be removed.
Do not remove the foam gasket on top of the compressor
cover unless removal is necessary to fit the unit under a
soffit. Removal of the gasket will cause loss in cooling
efficiency.
If installing under a solid soffit, after installation raise the
leveling legs so that the gasket is pressed snugly against
the soffit.
A. Gasket
B. Compressor
cover
A grounded 3 prong electrical outlet should be located within
a specified number of inches from the right-hand side
cabinets or end panel. See the chart following the graphic for
the number of inches required for your model. For more
information, see "Electrical Requirements."
The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. If the water shutoff valve is not in the cabinets, the
plumbing for the water line can come through the floor or the
back wall. See "Water Supply Requirements" for more
information.
IM PORTANT:
•
Observe all governing codes and ordinances.
t®TORX
is a registered trademark
of Saturn Fasteners,
Inc.
Advertisement
Table of Contents
