Overview; Precautions; Tools - Epson WorkForce 600 Service Manual
Hide thumbs
Also See for WorkForce 600:
- User manual (135 pages) ,
- Quick manual (56 pages) ,
- Network installation manual (41 pages)
Table of Contents
Advertisement
EPSON WorkForce 600/EPSON Stylus OFFICE TX600FW/BX600FW/EPSON Stylus SX600FW/ME OFFICE 700FW
4.1 Overview
This section describes procedures for disassembling the main components of EPSON
WorkForce 600/EPSON Stylus OFFICE TX600FW/BX600FW/EPSON Stylus
SX600FW/ME OFFICE 700FW. Unless otherwise specified, disassembled units or
components can be reassembled by reversing the disassembly procedure. Procedures
which, if not strictly observed, could result in personal injury are described under the
heading "WARNING". "CAUTION" signals a precaution which, if ignored, could
result in damage to equipment. Important tips for procedures are described under the
heading "CHECK POINT". If the assembly procedure is different from the reversed
disassembly procedure, the correct procedure is described under the heading
"REASSEMBLY". Any adjustments required after reassembly of components or parts
are described under the heading "ADJUSTMENT REQUIRED". When you have to
remove any components or parts that are not described in this chapter, refer to the
exploded diagrams in the appendix.
Read the following precautions before disassembling and assembling.
4.1.1 Precautions
See the precautions given under the heading "WARNING" and "CAUTION" in the
following columns when disassembling or assembling EPSON WorkForce 600/
EPSON Stylus OFFICE TX600FW/BX600FW/EPSON Stylus SX600FW/ME
OFFICE 700FW.
Disconnect the power cable before disassembling or
W A R N I N G
assembling the printer.
If you need to work on the printer with power applied, strictly
follow the instructions in this manual.
Always wear gloves for disassembly and reassembly to protect
your eyes from ink. If any ink gets in your eyes, wash your
eyes with clean water and consult a doctor immediately.
Always wear gloves for disassembly and reassembly to avoid
injury from sharp metal edges.
To protect sensitive microprocessors and circuitry, use static
discharge equipment, such as anti-static wrist straps, when
accessing internal components.
Never touch the ink or wasted ink with bare hands. If ink
comes into contact with your skin, wash it off with soap and
water immediately. If you have a skin irritation, consult a
doctor immediately.
DISASSEMBLY/ASSEMBLY
When transporting the printer after installing the ink cartridge,
C A U T I O N
pack the printer for transportation without removing the ink
cartridge and be sure to secure the Ink Cartridge to the printer
cover with tape tightly to keep it from moving.
Use only recommended tools for disassembling, assembling or
adjusting the printer.
Observe the specified torque when tightening screws.
Apply lubricants as specified. (See Chapter 6
"MAINTENANCE"
Make the specified adjustments when you disassemble the
printer. (See Chapter 5 "ADJUSTMENT"
When reassembling the Waste Ink Tube, make sure that the
tip of waste ink tube is placed in the correct position, otherwise
ink may leak.
When using compressed air products; such as air duster, for
cleaning during repair and maintenance, the use of such
products containing flammable gas is prohibited.
4.1.2 Tools
Use only specified tools to avoid damaging the printer.
Name
(+) Phillips screwdriver #1
(+) Phillips screwdriver #2
Flathead screwdriver
Flathead Precision screwdriver #1
Tweezers
Longnose pliers
Acetate tape
Nippers
Note * : All of the tools listed above are commercially available.
EPSON provides the tools listed with EPSON tool code.
Overview
(p163)
for details.)
(p150)
Table 4-1. Tools
EPSON Tool Code*
1080530
---
---
---
---
---
1003963
---
Confidential
Revision A
for details.)
90
- Quick Links:
- Service Manual
- Network Interface
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
