ICS 695GC Operator's Manual
Hide thumbs
Also See for 695GC:
- Operator's manual (48 pages) ,
- Quick start manual (4 pages) ,
- Operator's manual (40 pages)
Related Manuals for ICS 695GC
Summary of Contents for ICS 695GC
- Page 1 695GC / 695F4 OPERATOR’S MANUAL...
-
Page 3: Table Of Contents
695GC / 695F4 OPERATOR’S MANUAL INTRODUCTION / TABLE OF CONTENTS TITLE INTRODUCTION ¡ ® TABLE OF CONTENTS SYMBOLS & LABELS SAFETY TECHNICAL SPECIFICATIONS SET-UP OPERATION MAINTENANCE TROUBLESHOOTING REFERENCE... -
Page 4: Symbols & Labels
SYMBOLS & LABELS TITLE 695GC / 695F4 OPERATOR’S MANUAL THE FOLLOWING SYMBOLS & DEFINITIONS ARE FOUND THROUGHOUT THIS MANUAL AND ARE DESIGNED TO MAKE YOU AWARE OF POTENTIAL HAZARDS OR UNSAFE PRACTICES. A potentially hazardous situation exists which, if not avoided, WARNING could result in death or serious injury. -
Page 5: Safety
695GC / 695F4 OPERATOR’S MANUAL TITLE SAFETY THE FOLLOWING SYMBOL APPLIES TO ALL THE ITEMS LISTED ON THIS PAGE A potentially hazardous situation exists which, if not avoided, WARNING could result in death or serious injury. Chain breakage can result in high-speed ejection of parts, which can result in death or serious personal injury to operators or bystanders. - Page 6 SAFETY TITLE 695GC / 695F4 OPERATOR’S MANUAL THE FOLLOWING SYMBOL APPLIES TO ALL ITEMS LISTED ON THIS PAGE A potentially hazardous situation exists which, if not avoided, CAUTION may result in minor or moderate injury or property damage. including chain tensioning.
- Page 7 Note: The concrete chain saw is equipped with a 2-stroke engine and must always be run ® using a mixture of gasoline and ICS 2-stroke engine oil, or other high quality 2-stroke oil that has been formulated for air cooled power equipment. It is important to accurately measure the amount of oil to be mixed to ensure that correct mixture is obtained.
-
Page 8: Technical Specifications
TECHNICAL SPECIFICATIONS TITLE 695GC / 695F4 OPERATOR’S MANUAL £ ¤ ¥ ¦ ¤ § ¦ ¨ ¨ ¢... -
Page 9: Set-Up
695GC / 695F4 OPERATOR’S MANUAL TITLE SET-UP GUIDEBAR AND DIAMOND CHAIN INSTALLATION... - Page 10 SET-UP TITLE 695GC / 695F4 OPERATOR’S MANUAL GUIDEBAR AND DIAMOND CHAIN INSTALLATION CORRECT CHAIN TENSION CHAIN TOO TIGHT CHAIN TOO LOOSE ©...
- Page 11 695GC / 695F4 OPERATOR’S MANUAL TITLE SET-UP GUIDEBAR AND DIAMOND CHAIN INSTALLATION © ©...
-
Page 12: Operation
OPERATION TITLE 695GC / 695F4 OPERATOR’S MANUAL FUEL HANDLING CAUTION © © © ¢ © ¢ FUEL MIXING FUELING ©... - Page 13 695GC / 695F4 OPERATOR’S MANUAL TITLE OPERATION STARTING AND STOPPING A CONCRETE CHAIN SAW Never start a concrete chain saw without the bar, chain and side WARNING cover properly assembled. Failure to do so may result in serious injury. Always move a concrete chain saw at least 10 feet (3 m) away CAUTION from the fueling area before starting.
- Page 14 OPERATION TITLE 695GC / 695F4 OPERATOR’S MANUAL PRE-CUT CHECKLIST ¡ The single most important factor an operator can control to IMPORTANT increase chain life is to use adequate water pressure. Insufficient water supply will result in excessive wear to the chain, which can lead to loss of strength and chain breakage, and/or damage to the guidebar nose sprocket.
- Page 15 695GC / 695F4 OPERATOR’S MANUAL TITLE OPERATION CUTTING WITH THE 695GC ¡ CUTTING TIPS &...
- Page 16 OPERATION TITLE 695GC / 695F4 OPERATOR’S MANUAL CUTTING DUCTILE IRON PIPE WITH THE POWERGRIT ® UTILITY SAW CHAIN NEVER be cut. Support the work piece in such a way that the cut remains open during the cutting operation and when the cut is WARNING finished.