Table of Contents
Advertisement
Quick Links
User's Manual
UHBX-3S
HDMI On HDBaseT™ 1x3 Splitter with
Local Loop-out, RS232, & PoH
Split HDMI & Extend Video, Audio, RS232 & Power
upto 500 ft (150 m) on a single Cat6 cable
UMA1220 Rev B
© Copyright 2014. Hall Research, Inc. All rights reserved.
1163 Warner Ave Tustin, CA 92780, Ph: (714)641-6607, Fax (714)641-6698
Advertisement
Table of Contents
Related Manuals for Hall Research Technologies UHBX-3S
Summary of Contents for Hall Research Technologies UHBX-3S
- Page 1 User’s Manual UHBX-3S HDMI On HDBaseT™ 1x3 Splitter with Local Loop-out, RS232, & PoH Split HDMI & Extend Video, Audio, RS232 & Power upto 500 ft (150 m) on a single Cat6 cable UMA1220 Rev B © Copyright 2014. Hall Research, Inc. All rights reserved.
-
Page 2: Table Of Contents
UHBX-3S Table of Contents 1.0 Introduction 2.0 Features 3.0 Setup 3.1 Package Contents 3.2 Installation 4.0 Operation 4.1 Front Panel LEDs 4.2 EDID Management 5.0 Serial (RS-232) Commands 5.1 Serial Setup 5.2 Serial Commands 6.0 Troubleshooting 7.0 Specifications TRADEMARKS USED IN THIS MANUAL Hall Research and its logo are trademarks of Hall Research. -
Page 3: Introduction
UHBX-3S 1.0 Introduction The UHBX-3S is an HDMI 1.4 compliant splitter with one local HDMI output and 3 HDBaseT™ outputs for transmission to compatible receivers up to 150 meters/500 ft away (max distance is a function of receiver type). The Splitter supports HDCP, 3D, Deep Color, CEC, and 4Kx2K resolution. -
Page 4: Features
UHBX-3S additional +48V power supply must be connected to UHBX-3S. Note that the +48V power supply is not included with the UHBX-3S. UHBX-3S also works with UH-1BT-R and the UH-1BTX-R receivers. As shown in Figure 2 below. In this case each receiver is powered locally and the +48V power supply is NOT required at the sender. -
Page 5: Setup
UHBX-3S 3.0 Setup 3.1 Package Contents All UHBX-3S units are shipped with +5V power supply, a 1m HDMI cable and a male-to-female RS-232 cable. 3.2 Installation Remote Display 1 UHBX-3S UHBX-R-PD Cat 6 Video Source Cat 6 Remote UHBX-R-PD Display 2... - Page 6 Output port RS-232 Cable numbers & to manage EDID. +48V Figure 4 – Two UHBX-3S units daisy-chained together A maximum of 7 splitters can be daisy chained in this manner. This would allow 21 remote displays and one local display.
-
Page 7: Operation
Output 4.0 Operation Make connections as shown in Figure 3 and power up the UHBX-3S. If the UHBX-R-PD is used as the receiver, make sure the optional 48V power supply is also connected to the sender. In this case the PoH LED will be lit in about 3 seconds to indicate that the receiver is getting power. -
Page 8: Edid Management
EDID of the TV connected to the output(s) is passed to the source. In Emulate mode the UHBX-3S allows the user to send an EDID table that is stored in the splitter itself (independent of the sinks). The EDID mode is selectable from the front panel. -
Page 9: Serial Commands
XB,n command prior to sending data to individual outputs By Default power management is turned on in the UHBX-3S. This means that if there is no video or no display connected (Hot Plug not active), the unit will put the HDBaseT links in low power mode. -
Page 10: Troubleshooting
If you are using UH-1BTX-R that does not have a LR switch, you can force the link in LR mode from the UHBX-3S using the Windows GUI software through the USB port. The unit will remember the last setting. -
Page 11: Specifications
UHBX-3S 7.0 Specifications Input & Output ports Input Port 1x HDMI Female (Type A) Output Port 1x HDMI Female (Type A), 3x RJ45 connectors Video Standards DVI (single link) and HDMI (compliant with 12 bit color depth, 3D video) Signal type... - Page 12 UHBX-3S © Copyright 2014. Hall Research, Inc. All rights reserved. 1163 Warner Ave., Tustin, CA 92780 Ph: (714)641-6607...