Advertisement
Quick Links
Approved for use with Valor heater models 530 and 922 only
WARNING
!
A barrier designed to reduce the risk of burns from the hot viewing
glass is provided with this appliance and shall be installed
for the protection of children and other at-risk individuals.
Note: This kit must be installed or serviced by a qualifi ed
installer, service agency or gas supplier. These instructions
are to be used in conjunction with the main installation
instructions for the above listed heater model.
WARNING: If the information in these instructions is not
followed exactly, a fi re or explosion may result causing
property damage, personal injury or loss of life.
Valor models 530 and 922 are suitable for installation in a
bedroom or bed sitting room.
FOR ARCH INSTALLATION WITH A VALOR 530 ENGINE, READ
FOR ARCH INSTALLATION WITH A VALOR 922 ENGINE, READ
FOR 530 AND 922 ENGINES' CONFIGURATIONS AND VENTING, REFER
TO MAIN INSTALLATION BOOKLETS SUPPLIED WITH THE ENGINES.
4001125-09
©2013, Miles Industries Ltd.
P
ORTRAIT
Cast Arch Fronts
539, 549 & 550 Series
Installation and Owner's Manual
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
INSTRUCTIONS FROM PAGE 2.
INSTRUCTIONS FROM PAGE 8.
I NSTALL ER
Leave this manual
with the appliance.
C O NSU M ER
Retain this manual
for future reference.
Note: Valor models 530 and
922 may be installed in an
aftermarket permanently
located manufactured
(mobile) home, where not
prohibited by local codes.
Valor models 530 and 922
are only for use with the type
of gas indicated on their
rating plate. They are not
convertible for use with other
gases, unless a certifi ed kit is
used.
Advertisement
Related Manuals for Valor PORTRAIT 539
Summary of Contents for Valor PORTRAIT 539
- Page 1 ORTRAIT Cast Arch Fronts 539, 549 & 550 Series Approved for use with Valor heater models 530 and 922 only Installation and Owner’s Manual WARNING I NSTALL ER Leave this manual HOT GLASS WILL with the appliance. CAUSE BURNS. DO NOT TOUCH GLASS C O NSU M ER UNTIL COOLED.
- Page 2 Kit Contents Insulation Blanket (2 layers) 539AFB/P Windsor Arch & 550CAP Classic Arch (with plate) 1 Outer cast iron arch (w/plate) Top Baffle 1 Barrier screen 1 Inner cast iron arch Air Deflector 1 Hearth fender, cast iron 2 Side mounting brackets, sheet metal 4 Spacers, sheet metal Stand-off Spacers (2) 1 Top baffl...
-
Page 3: Hearth Requirements
Applications Floor Requirements The 530 heater is approved for installation directly The Valor model 530 heater with the 539 or 550 Cast on any combustible material other than soft fl ooring Arch Fronts comes ready for installation as a zero material such as carpet or vinyl. - Page 4 Dimensions & Clearances— 24” 20” Note: 549 Windsor Arch front (without back plate) 556CLA Adapter (top or rear outlet) Required ‘X’ Mantel Top or Rear Outlet 2-1/2” 6” Side Mounting Brackets Min. 4” Max. 8” deep mantel leg at edge of arch ‘Y’...
-
Page 5: Installation
Installation 3. Locate Side Mounting Brackets as shown and line up the mounting holes in the side of the heater body. 1. Fit Top Baffl e under the top panel of the appliance Secure the side brackets to the heater using the case. - Page 6 6. Hang the Inner Cast Arch. Insert the mounting 8. Install the barrier screen by snapping the barrier hooks into the notches in the outer cast plate screen’s top part to the inner arch. Then slide the as shown. The fi t or gap between the inner cast screen up slightly under the hood, snap the bottom of arch and the outer cast plate may be tightened by the barrier to the inner arch and slide the screen back...
- Page 7 Cleaning WARNING DO NOT TOUCH THE BARRIER SCREEN, DO NOT TOUCH THE BARRIER SCREEN, THE CAST FRONT OR THE GLASS WHILE THE CAST FRONT OR THE GLASS WHILE THEY ARE HOT! THEY ARE HOT! Let the fireplace cool first Let the fireplace cool first before cleaning it.
- Page 8 (539AFB, 539AFP, 549AFB, 549AFP) RONT NSTALLATION WITH All Arch fronts mounted to 922 fi reboxes require a 540 WDK wire guard and mounting hardware. Note: The bottom of the fi rebox must be installed fl ush with the fi nished hearth height or the cast front will not install properly.
- Page 9 Installation 3. Fasten the top fi ller piece to the back of the outer cast arch. 1. Install the mounting brackets and burner tray cover to the fi rebox as per instructions supplied with the 922 engine. 4. Mount outer cast arch to brackets on fi rebox as shown below.
- Page 10 (539AFB, 539AFP, 549AFB, 549AFP, 550CAP) EPAIRS ARTS Description 539 Series 549 Series 550 Series Black Polished Black Polished Hearth Fender 4000241AH 4000241 4000241AH 4000241 4001104 Inner Cast Arch 4000240AH 4000240 4000240AH 4000240 4001094 Hearth Baffl e 4000347 4000347 4000347 4000347 4001100AH Outer Cast Arch 4000225AH...
- Page 11 Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication. Designed and Manufactured by / for Miles Industries Ltd. 190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1 Tel. 604-984-3496 Fax 604-984-0246 www.valorfi replaces.com...