KD-S680 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
KD-S680 3 7 63 1515 0 Preventing static electricity 1.Grounding to prevent damage by static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
KD-S680 3 7 63 1515 0 Disassembly method <Main body> Removing the front panel assembly (See Fig.1) Press the eject button in the lower right part of the front panel. Remove the front panel assembly from the body. Front panel assembly Eject button Fig.1...
KD-S680 3 7 63 1515 0 Removing the heat sink (See Fig.4) Remove the three screws A on the left side of the body. Heat sink Fig.4 Joints b Removing the bottom cover (See Fig.5 and 6) Bottom cover...
KD-S680 3 7 63 1515 0 Removing the main board (See Fig.7 and 8) Prior to performing the following procedure, remove the front panel assembly, the front chassis assembly, the heat sink and the bottom cover. Remove the screw B, the four screws C and the...
Page 7
KD-S680 3 7 63 1515 0 Removing the control switch board (See Fig.10 to 12) Prior to performing the following procedure, remove the front panel assembly. Remove the four screws G attaching the rear cover on the back of the front panel assembly.
KD-S680 3 7 63 1515 0 Damper bracket <CD mechanism section> CD mechanism assembly Removing the CD mechanism control board (See Fig.1 and 2) Unsolder the part a and b on the CD mechanism control board. Remove the stator fixing the CD mechanism control board and the damper bracket (To remove the stator smoothly, pick up the center part).
Page 9
KD-S680 3 7 63 1515 0 Damper bracket assembly CD mechanism Removing the CD mechanism assembly (See Fig.1, 6 to 9) Prior to performing the following procedure, remove the CD mechanism control board and the front bracket (loading motor).
KD-S680 3 7 63 1515 0 Removing the feed motor assembly FD screw Part i Feed motor assembly (See Fig.10) Prior to performing the following procedure, remove the CD mechanism control board, the front bracket Part j (loading motor) and the CD mechanism assembly.
6. Digital tester FM 87.5MHz ~ 107.9MHz 7. Tracking offset meter MW 530kHz ~ 1710 kHz 8. Test Disc JVC :CTS-1000 9. Extension cable for check EXTGS004-26P 1 Dummy load Exclusive dummy load should be used for AM,and FM. For FM dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered...
KD-S680 3 7 63 1515 0 Flow of functional operation until TOC read Power ON • When the laser diode correctly Set Function to CD • When the pickup correctly moves emits to the inner area of the disc...
KD-S680 3 7 63 1515 0 Feed Section Check CD 9V Is the voltage output at Is the wiring for IC521 Is 5V present at IC581 and 5V. IC521 pin "53" 5V or 0V? (90) ~ (100) correct? pin "11"? Check the vicinity of IC521.
KD-S680 3 7 63 1515 0 Maintenance of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens with a alcohol soaked cotton swab. (2) Life of the laser diode When the life of the laser diode has expired, the following symptoms will appear.
Page 18
3 7 63 1515 0 UPD178078GF-559 (IC701) : System CPU 1.Pin layout 2.Pin function (1/2) Symbol FUNCTION No use BUSINT JVC bus communication line BUSSI JVC bus communication line BUSSO JVC bus communication line JBUS-SCK JVC bus communication line 6,7,8...
Page 19
KD-S680 3 7 63 1515 0 2.Pin function (2/2) UPD178078GF-559 Symbol FUNCTION GNDPLL AMEO PLL error output for AM FMEO PLL error output for FM IC(VPP) Setting to write for flash RESET System reset CD mech switch REMOCON Remocon input...
Page 20
KD-S680 3 7 63 1515 0 LA4743K(IC302):Power AMP 1.Block diagram 2200 F 0.022 F Vcc 1/2 Vcc 3/4 IN 1 OUT 1+ 0.22 F OUT 1- PWR GND1 Protective circuit OUT 2+ IN 2 OUT 2- 0.22 F PWR GND2...
Page 21
KD-S680 3 7 63 1515 0 2.Terminal layout 3.Pin function LA4743K Pin No. Symbol Function Header of IC Power GND OUTRR- Outpur(-) for front Rch STBY Stand by input Output (+) for front Rch OUTRR+ Power input VCC1/2 OUTRF-...
Page 25
KD-S680 3 7 63 1515 0 2. Pin function (2/2) TC9490FA Symbol Function RFCT RFRP signal center level input pin. RFZI RFRP signal zero-cross input pin. RFRP RF ripple signal input pin. Focus error signal input pin. SBADTEI Sub-beam adder signal input pin.
Page 26
KD-S680 3 7 63 1515 0 NJM4565M-WE (IC571) : Ope. amp A OUTPUT A INPUT B OUTPUT A INPUT B INPUT B INPUT RPM6938-SV4(IC602) : Remote sensor 1.Block diagram L 13942296513 Comp Rout Detector conversion trimming circuit magnetic shield...
Page 27
KD-S680 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED MOBILE ELECTRONICS DIVISION PERSONAL & MOBILE NETWORK BUSINESS UNIT. 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan 200112 (No.49665) http://www.xiaoyu163.com...
KD-S680 3 7 63 1515 0 PARTS LIST [ KD-S680 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix J -------------- Northern America L 13942296513 - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1) 3- 5 CD mechanism assembly and parts list (Block No.MB)
KD-S680 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. L 13942296513 u163 http://www.xiaoyu163.com...
Page 37
KD-S680 3 7 63 1515 0 Parts list (General assembly) Block No. M1MM Item Description Parts number Parts name Q'ty Area ------------ CD MECHA (1325) FSJC1029-401 TOP CHASSIS FSMH3001-202 HEAT SINK FSKM3011-002 BOTTOM COVER FSMA3004-203 INSULATOR SCREW 3 CHASSIS+MECHA BKT...
Page 38
KD-S680 3 7 63 1515 0 Parts list (General assembly) Block No. M1MM Item Description Parts number Parts name Q'ty Area QYSDST2606Z SCREW 1 FOR ANT QYSDSF3006Z SCREW 1 FOR LINE OUT QYSDST2606Z SCREW 3 16P & REG BKT...
KD-S680 3 7 63 1515 0 CD mechanism assembly and parts list Block No. Grease G-31SA TN-CCD1001Z-138S G-31SA(Bottom side) RX-405 L 13942296513 u163 106 29 http://www.xiaoyu163.com...
Page 40
KD-S680 3 7 63 1515 0 Parts list (CD mechanism) Block No. MBMM Item Description Parts number Parts name Q'ty Area 30310101T FRAME 30310103T DANPER PIN 30310107T UPPER PLATE 30310108T SEL STOP PLATE 30310142T SEL ARM (L)L SEL ARM (R)L...
Page 41
KD-S680 3 7 63 1515 0 Parts list (CD mechanism) Block No. MBMM Item Description Parts number Parts name Q'ty Area 68150242T CONNECTOR 1 TKC-W26X-A1 30311105T SOPPORT PLATE 30311138T GR MT BLK(N) 30311109T LDG GEAR (2) 30311110T LDG GEAR (3)
Page 42
KD-S680 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area QERF1CM-106Z E CAPACITOR 10MF 20% 16V C 300 NCB31HK-223X C CAPACITOR...
Page 43
KD-S680 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 553 NDC31HJ-100X C CAPACITOR D 702 UDZS6.2B-X SI DIODE C 554...
Page 44
KD-S680 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area R 24 NRSA02J-222X MG RESISTOR R 513 NRSA63J-102X MG RESISTOR R 25...
Page 45
KD-S680 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area R 723 NRSA63J-473X MG RESISTOR R 724 NRSA63J-473X MG RESISTOR R 725 NRSA63J-473X MG RESISTOR R 726 NRSA63J-0R0X...
Page 46
KD-S680 3 7 63 1515 0 Electrical parts list (Front board) Block No. 02 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 601 NCB31HK-223X C CAPACITOR R 637 NRSA63J-182X MG RESISTOR C 602...
Page 47
KD-S680 3 7 63 1515 0 < M E M O > L 13942296513 u163 3-13 http://www.xiaoyu163.com...