Using The Ramp Function - Sony SRW-9000 Operation Manual
Hide thumbs
Also See for SRW-9000:
- Operation manual (221 pages) ,
- Brochure & specs (8 pages) ,
- Operation manual (177 pages)
Table of Contents
Advertisement
SELECT FPS: ON
FPS
FRAME
FORMAT
(target
(system
frame
frame
frequency)
frequency)
23.98
23.98
24
24
25
24
25
29.97
23.98
29.97
30
24
25
50
24
25
50
59.94
23.98
29.97
59.94
60
24
25
50
FPS
FRAME
FORMAT
(target
(system
frame
frame
frequency)
frequency)
–
23.98
24
25
29.97
50
59.94
Using the Ramp Function
The Ramp function allows you to achieve speed
variations by changing the number of frames shot
(FPS) during Select FPS recording.
There are two Ramp modes: manual mode, in
which you specify upper and lower limits and
manually vary the speed within that range, and
auto mode, in which you specify start and end
frames and a duration, and allow the unit to vary
the speed automatically according to preset rules.
Proceed as follows to set up the Ramp function.
106
Select FPS Function
SIGNAL (signal format)
4:2:2
4:4:4
4:4:4
(YCbCr)
SQ
HQ
(RGB)
(RGB)
a
s
s
a
s
s
a
s
s
a
s
s
a
s
s
a
s
s
a
s
s
a
s
s
a
s
z
a
s
z
a
z
z
a
s
z
a
s
z
a
z
z
a
s
z
a
s
z
a
z
z
SIGNAL (signal format)
4:2:2
4:4:4
4:4:4
(YCbCr)
SQ
HQ
(RGB)
(RGB)
a
s
s
a
s
s
a
s
s
a
s
s
a
z
z
a
z
z
1
In the SYSTEM Setup menu, select
EDIT >RAMP.
A setting window opens.
S y s t e m S e t u p
FORMAT
REFERENCE
TEST SG
LCD
KEY MAP
KEY INHI
MAP
REMOTE/LCKAL
LCL
SERVO
REC INHI
OFF
EDIT
POWER
BATTERY
OTHERS
C A S S O U T
S R W - 9 0 0 0
2
Select the Ramp function operating
mode from the following.
Auto(Linear): Varies the number of frames
shot (FPS) linearly.
Auto(Inverse): Varies the inverse of the
number of frames shot (frm) linearly.
Auto(Even): Varies the number of frames
shot so that there are the same number of
frames for each frequency.
Auto(User): Varies the number of frames
shot along a user-specified curve.
Manual: Varies the number of frames shot
manually within preset upper and lower
limits.
Off: Varies the number of frames shot
manually with no range limits.
3
Make the settings required by the
selected mode.
When Auto(Linear), Auto(Inverse), or
Auto(Even) was selected, see the next section,
"To vary the number of frames shot
automatically".
When Auto(User) was selected, see "To vary the
number of frames shot along a user-specified
curve" (page 107).
When Manual or Off was selected, see "To vary
the number of frames shot manually" (page
108).
Edit Config
RAMP
MANU
Auto Spd1
1
Auto Spd2
20
Duration
5s
Load Curve
Manu Spd1
1
0 0 : 00 : 0 0 : 0 0
T C R
Advertisement
Table of Contents
