Table of Contents
Advertisement
Your grinder comes with two reversible flanges to
accommodate a wide variety of different accessories. Make
sure the correct sides of the flanges are being used ensuring
no excessive play between the accessory and the flanges.
Mounting
Place the inner flange (5) on the grinder spindle (7) (fig.
C1)
Place the wheel (14) against the flange. Screw the
threaded flange (6) onto the spindle (7). (fig. C2).
Make sure that the threaded outer flange (6) is facing in
the correct direction for the type of disc fitted. For grinding
discs, the flange (6) is fitted with the raised portion facing
towards the disc (fig. C3).
Press in the spindle lock button (3) and rotate the spindle
until it locks. Keeping the lock button pressed in, tighten
the threaded flange (6) with the spanner (15) provided
(fig. D)
Release the spindle lock.
Removing
Follow the procedure above in reverse order.
Instruction for Use
Always observe the safety instructions and applicable
regulations.
Ensure all materials to be ground are secured in palce.
Apply only a gentle pressure to the tool. Do not exert side
pressure on the grinding wheel or cutting disc.
Avoid overloading. Should the tool become hot, let it run a
few minutes under no load condition.
Slide after push
Prior to Operation
Install the appropriate guard and disc or wheel. Do not
use excessively worn discs or wheels.
Be sure the inner and threaded flanges are mounted
correctly.
Make sure the disc or wheel rotates in the direction of the
arrows on the accessory and the tool.
@
Switching On And Off (Fig. A)
Make sure that the switch is in the "OFF" position
before plugging in.
To run the tool, slide the ON/OFF switch (1) forward to the
"ON" position.
To stop the tool, slide the switch backwards to the "OFF"
position.
Always switch off the tool when work is finished and before
@
unplugging.
Do not switch the tool ON and OFF when under load.
Handy Hints (Fig. G)
Hold your angle grinder with one hand on the body and the
other hand firmly around the side handle.
Always position the guard so that as much of the exposed
disc as possible is pointing away from you.
Be prepared for a stream of sparks when the disc touches
the metal.
Grinding (Fig. H)
Use a depressed center Type 27 disc. Hold the tool at an
angle of approximately 20º-30º to work for grinding.
@
Edge Grinding and Cutting
Do not use edge grinding wheels for surface
grinding applications because these wheels are
not designed for side pressures encountered with
surface grinding. Wheel breakage and injury may
result.
Edge grinding can be performed with type 27
wheels designed and specificed for this purpose.
Protect yourself during edge grinding by directing
the open side of the guard toward a surface. Edge
grinding wheels should contact the work surface
only at the edge of the wheel, not on the top or
bottom of the wheel.Side pressure on the wheel
could lead to breakage of the wheel.
Maintenance
Your Black and Decker power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning. Your tool is not
user-serviceable. Take the tool to an authorized Black and
Decker repair agent. This tool should be serviced at regular
intervals or when showing a noticeable change in performance.
Lubrication
Black and Decker power tools are properly lubricated at the
factory and are ready for use. Tools should be relubricate
regularly , depending on usage. This lubrication should only
be attempted by trained power tool repair persons, such as
those at Black and Decker service centers or by other
qualified service personnel.
@
Cleaning
Warning: unplug the tool before you use a cloth to
clean the housing.With the motor running, blow dirt
and dust out of all air vents with dry air at least once
a week. Wear safety glasses when performing this.
Exterior plastic parts may be cleaned with a damp
cloth and mild detergent. Although these parts are
highly solvent resistant, NEVER use solvents.
ENGLISH
7
Advertisement
Table of Contents
