Integrated high definition dlp projection television (128 pages)
Summary of Contents for Toshiba 56HM195
Page 1
When repairing these green products, use the parts described in this manual and lead-free solder (*2). For (*1) and (*2), see the next page. Published in Japan Sep. 2005 (YC) TOSHIBA CORPORATION 2005...
Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.
SAFETY INSTRUCTIONS SAFETY PRECAUTION WARNING: Service should not be attempted by anyone unfamiliar with the necessary precautions on this receiver. The following are the necessary precautions to be observed before servicing this chassis. 1. An isolation transformer should be connected in the power line between the receiver and the AC line before any service is performed on the receiver.
SERVICE MODE 1. ENTERING SERVICE MODE 1) Press MUTE button twice 2) Press MUTE button 3) While pressing the MUTE button, on Remote Control. again and keep pressing. press MENU button on TV set. MUTE (Service mode display) 2. DISPLAYING THE ADJUSTMENT MENU 1) Press MENU button on Remote Control.
Page 5
SELF DIAGNOSTIC FUNCTION 1) Press “9” button on Remote Control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC’s is executed properly. 2) During diagnosis, the following displays are shown. Firmware : Version information of microprocessor In case of file name : HM195 and Version : 1401 indicates[HM195_1401].
Page 6
VERSION CHECK MODE 1) Press “9” button twice on Remote Control during display of adjustment menu in the service mode. The version of main MPU will begin to check. 2) During Version Check, the following displays are shown. MAIN MPU : Version information of microprocessor In case of file name : HM195, Version 1401 for Code Program Version and (U15) for OSD Version indicates [HM195_1401(U15)]...
Page 7
8. STATUS CHECK MODE 1) Press “9” button thrice on Remote Control during display of adjustment menu in the service mode. The status of this model will begin to check. 2) During Status Check, the following displays are shown. MAIN : Main source information : Display RF position number (1 - 135) on the main screen, or Input Source (HDMI1/2, DVI, AUDIO etc.) MAIN FORMAT :...
Page 8
TV cabinet are not vals 4 times (repeat). covered, blocked, or dusty. Turn ON the TV again. If the problem persists, contact a Toshiba Authorized Service Center. Yellow is OFF; Abnormal operation Turn OFF the TV and unplug the power cord.
SETTING & ADJUSTING DATA SERVICE MODE ADJUSTING ITEMS AND DATA IN THE SERVICE MODE: Item Name of adjustment Preset Data Item Name of adjustment Preset Data RCUT R CUT OFF VPOS V-POSITION GCUT G CUTOFF CWDH COLOR WHEEL DELAY (HIGH) BCUT B CUT OFF CWDL...
LAMP UNIT REPLACEMENT Cautions when replacing LAMP UNIT (E998Z; PJ-D95-LMP) The light source for this TV is a mercury lamp with internal atmospheric pressure that increases during use. The lamp has a limited service life that varies depending on user settings. If you use the lamp beyond its service life: you may notice a reduction in the colors and/or brightness of the pic- ture;...
Page 11
Turn off the TV and unplug the power cord. Grasp the lamp unit handle and gently pull the lamp unit straight out of the TV. Set the old lamp unit aside. STOP! Allow the lamp to cool for at least one (1) hour before replacing it.
Page 12
Reattach the lamp unit door, making sure to insert the hooks on the left side of the lamp unit door inside the opening in the TV cabinet. Insert the hooks inside the TV cabinet opening. Lamp unit door Replace the screw and hand-tighten using a manual screwdriver.
LIGHT ENGINE REPLACEMENT Cautions when replacing LIGHT ENGINE LIGHT ENGINE UNIT: A271 : LV-682 TB (Including with E998Z, SK01 to SK04, SK06,SK08 and SK09.) LIGHT ENGINE is a heart of the TV and emits high heat. Make sure to replace it after turning off the TV and wait for sufficient cool down.
PARTS REPLACEMENT IN LIGHT ENGINE Replacement of Lamp FAN (SK01) Replacement of Ballast FAN (SK03) 1-1. Replace the FAN for cooling Lamp (SK01), remove the 2-1. Replace the FAN for cooling Ballast Power Unit (SK03), 4 screws on the FAN Hood, and remove the 4 pins by remove the Ballast Hood, and remove the 2 screws on the pressing toward allows using a screwdriver, and the Ballast Case Cover.
Page 15
Ballast FAN (SK03) 3-2. Remove the 2 screws from the bracket, and then remove the FAN for cooling Formatter Board (SK02). 3-3. Disconnect and replace the FAN transfer cable between Ballast and Formatter Boards (SK09). DMD FAN (SK02) 2 screws 4 pins Replacement of DMD FAN (SK02) and FAN Transfer Cable (SK09)
Page 39
SCHEMATIC DIAGRAM MODEL : 56/62/72HM195 WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON PAGE 3 OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
CIRCUIT BLOCK DIAGRAM BACK AV SIGNAL BOARD DDR SDRAM DDR SDRAM FLI8532 CORTEZ VBI Data PJ22 VIDEO Processor YCbCr CS 1/2 Analog DCDi Video CVBS Front MADi E 1-3 Decoder Scaling (16port) TUNER SC 1-3 ANT 1/2 LVDS RF-SW TIF OUT Chanel CVBS Process...
Page 44
OPTICAL ENGINE UNIT Smooth Picture Control Board Projection Lens Lamp Light Tunnel Chip From RTIR Prism Color Wheel Color Wheel Sensor Board Drive Ballast Board Ballast Engine DMD MAIN POWER FAN EX FAN EX FAN DMD FAN DMD Mother Board TRANS E2.5 E2.5...