free hit counter
Baby Lock Soprano BLMSP Instruction And Reference Manual
  1. Manuals
  2. Brands
  3. Baby Lock Manuals
  4. Sewing Machine
  5. Soprano BLMSP
  6. Instruction and reference manual

Baby Lock Soprano BLMSP Instruction And Reference Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Baby Lock Soprano BLMSP

Summary of Contents for Baby Lock Soprano BLMSP

  • Page 3: Introduction

    Never operate this machine if it has a damaged cord or plug, if it is not working properly, has been dropped or damaged, or water is spilled on the unit. Return the machine to the nearest authorized Baby Lock retailer for examination, repair, electrical or mechanical adjustment.
  • Page 4 For repair or adjustment: • If the light unit is damaged, it must be replaced by an authorized Baby Lock retailer. • In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the Instruction and Reference Guide to inspect and adjust the machine yourself.
  • Page 5 • Always replace the fuse cover. Never use plugs with the fuse cover omitted. • If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your authorized Baby Lock retailer to obtain the correct lead.

  • Page 6: About This Manual

    ABOUT THIS MANUAL ABOUT THIS MANUAL This manual was written for several machine models. The screen displays may differ from the ones displayed on your machine. Refer to the Quick Reference Guide for details on accessories, settings screen and pre-programmed stitch patterns. First, read “Functions available with each model”...

  • Page 7: Table Of Contents

    CONTENTS CONTENTS INTRODUCTION..........i Hands-free raising and lifting of the presser foot ....43 Stitch Setting Chart ..........44 IMPORTANT SAFETY INSTRUCTIONS ....i ABOUT THIS MANUAL ........iv Sewing WHAT YOU CAN DO WITH THIS MACHINE ..iv Basic operations Chapter 1 SEWING ATTRACTIVE FINISHES Chapter 1 GETTING READY...
  • Page 8 CONTENTS Decorative sewing Chapter 1 CHARACTER / DECORATIVE STITCHES Sewing the Various Built-in Decorative Patterns ..2 Selecting stitch patterns ............2 Deleting a pattern..............3 Sewing attractive finishes ............3 Basic sewing ................4 Combining patterns ..............5 Repeating combined patterns ..........5 Checking the selected pattern..........

  • Page 9: Basic Operations

    Basic operations This section provides details on the initial setup procedures as well as descriptions of this machine’s more useful functions. Page number starts with “B” in this section. Chapter1 GETTING READY............B-2 Chapter2 STARTING TO SEW ..........B-31...

  • Page 10: Chapter 1 Getting Ready

    Names of Machine Parts and Their Functions GETTING READY Chapter Names of Machine Parts and Their Functions The names of the various parts of the machine and their functions are described below. Before using the machine, carefully read these descriptions to learn the names of the machine parts and their locations. Machine ■...

  • Page 11: Needle And Presser Foot Section

    Names of Machine Parts and Their Functions Needle and presser foot section Measurements on the needle plate, bobbin cover (with mark) and needle plate cover The measurements on the bobbin cover are references for patterns with a middle (center) needle position. The measurements on the needle plate and the needle plate cover are references for stitches with a left needle position.

  • Page 12: Operation Buttons

    Names of Machine Parts and Their Functions Operation buttons Operation panel and operation keys d e f 1 “Start/Stop” button Press the “Start/Stop” button to start or stop sewing. The machine stitches at a slow speed at the beginning of sewing while the button is pressed.

  • Page 13: Using The Flat Bed Attachment

    Names of Machine Parts and Their Functions E OK key Using the flat bed attachment Press to apply the selection or perform the operation. F Numeric keys Pull the top of the flat bed attachment to open the accessory Use these keys to quickly select one of the ten most often used compartments.

  • Page 14: Included Accessories

    Names of Machine Parts and Their Functions Included accessories Refer to the Quick Reference Guide for the included accessories and their part codes for your machine model. Note • (For U.S.A. only) Foot controller: Model T This foot controller can be used on machine models: BLMSP, BLMLR and BL210A. Functions available with each model Using the utility stitch tables in the “Sewing”...

  • Page 15: Turning The Machine On/Off

    If the cord or plug is damaged, take the machine to your authorized Baby Lock retailer for repairs before continuing use. • Unplug the power cord if the machine is not to be used for a long period of time. Otherwise, a fire may result.

  • Page 16: Turning On The Machine

    Turning the Machine On/Off Turning on the machine Turning off the machine When you are finished using the machine, turn it off. In Make sure that the machine is turned off (the main addition, before transporting the machine to another location, power switch is set to “...

  • Page 17: Lcd

    Viewing the LCD When the power is turned on, the LCD comes on, and the following screen is displayed. The screen will vary slightly depending on your machine model. The screen is changed using the keys below the LCD. Display Item Name Explanation Page...

  • Page 18: Settings Screen

    Settings screen Press to change various sewing machine operations and sewing settings. Press to move to previous/next pages. * You can also move to next pages by pressing Press to select the next/previous items. * Press (Downward arrow) to select the next item. * Press (Upward arrow) to select the previous item.
  • Page 19 9 Changes the size of the stitch pattern. For details, refer to “Changing the pattern size” in the “Decorative sewing” section. 0 Adjusts the up and down position of the pattern. For details, refer to “Realigning the pattern” in the “Decorative sewing” section. A Adjusts the left and right position of the pattern.

  • Page 20: Choosing The Display Language

    Adjust the input sensitivity by pressing the “-” or “+” Choosing the display language key. • The lower the setting, the less sensitive the keys will Press be; the higher the setting, the more sensitive the keys will be. The default setting is “3”. Select (Language) display.

  • Page 21: Winding/Installing The Bobbin

    Winding/Installing the Bobbin Winding/Installing the Bobbin Place the bobbin on the bobbin winder shaft so that the spring on the shaft fits into the notch in the bobbin CAUTION Press down on the bobbin until it snaps into place. • Only use the Bobbin (part code: X52800-120) designed specifically for this machine.
  • Page 22 Winding/Installing the Bobbin Slide the spool cap onto the spool pin. Memo Slide the spool cap as far as possible to the right, as shown, with the rounded side on the left. • When sewing with fine, cross-wound thread, use the small spool cap, and leave a small space between the cap and the spool.
  • Page 23 Winding/Installing the Bobbin While holding the thread near the spool with your right While holding the thread with your left hand, wind the hand, as shown, pull the thread with your left hand, thread that was pulled out clockwise around the and then pass the thread behind the thread guide cover bobbin five or six times with your right hand.

  • Page 24: Installing The Bobbin

    Winding/Installing the Bobbin Press the “Start/Stop” button once to start winding the Installing the bobbin bobbin. When the foot controller is plugged in, press down on the foot controller. Install the bobbin wound with thread. You can begin sewing immediately without pulling up the bobbin thread by simply inserting the bobbin in the bobbin case and guiding the thread through the slit in the needle plate cover.
  • Page 25 Winding/Installing the Bobbin Slide the bobbin cover latch to the right. Memo • The order that the bobbin thread should be passed through the bobbin case is indicated by marks around the bobbin case. Be sure to thread the machine as indicated. 1 Bobbin cover 2 Latch Remove the bobbin cover.
  • Page 26 Winding/Installing the Bobbin Note • If the thread is not correctly inserted through the tension-adjusting spring of the bobbin case, it may cause incorrect thread tension. 1 Tension-adjusting spring Reattach the bobbin cover. Insert the tab in the lower-left corner of the bobbin cover, and then lightly press down on the right side.

  • Page 27: Upper Threading

    Upper Threading Upper Threading Turn on the machine. CAUTION Raise the presser foot lever to raise the presser foot. • Three spool cap sizes are available, allowing you to choose a spool cap that best fits the size of spool being used. If the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the needle may break.
  • Page 28 Upper Threading Place the spool of thread onto the spool pin. While using your right hand to lightly hold the thread passed under the thread guide plate, pass the thread Slide the spool onto the pin so that the spool is through the guides in the order shown below.

  • Page 29: Threading The Needle

    Upper Threading Slide the thread behind the needle bar thread guide. Cut the thread with the cutter on the left side of the machine. The thread can easily be slid behind the needle bar thread guide by holding the thread in your left hand, then feeding the thread with your right hand, as shown.

  • Page 30: Threading The Needle Manually (Without Using The Needle Threader)

    Upper Threading Lower the needle threader lever on the left side of the Threading the needle manually (without machine until it clicks, and then slowly return the lever to its original position. using the needle threader) When using specialty thread, such as transparent nylon thread, a wing needle or a twin needle which cannot be used with the needle threader, thread the needle as described below.

  • Page 31: Using The Twin Needle

    Upper Threading While lightly holding the upper thread with your left Using the twin needle hand, press (Needle position button) twice to raise the needle. With the twin needle, you can sew two parallel lines of the same stitch with two different threads. Both upper threads should have the same thickness and quality.
  • Page 32 Upper Threading Insert the horizontal spool pin onto the bobbin winder Without passing the thread through the needle bar shaft. thread guide, manually thread the right needle. Insert the horizontal spool pin so that it is perpendicular Insert the thread through the eye of the needle from the to the bobbin winder shaft.
  • Page 33 Upper Threading Start sewing. • For details on starting to sew, refer to “STARTING TO SEW” on page B-31. → Two lines of stitching are sewn parallel to each other. Note • When changing the sewing direction, press (Needle position button) to raise the needle from the fabric, and then raise the presser foot lever and turn the fabric.

  • Page 34: Replacing The Needle

    Replacing the Needle Replacing the Needle Be sure to observe the following precautions concerning the handling of the needle. Failure to observe these precautions is extremely dangerous, for example, if the needle breaks and fragments are dispersed. Be sure to read and carefully follow the instructions below.

  • Page 35: Checking The Needle

    Replacing the Needle Press Checking the needle • If is pressed while the presser foot is raised, an error message appears: “Lower the presser foot Sewing with a bent needle is extremely dangerous since the lever.” or “Use the presser foot lifter button to lower needle may break while the machine is being operated.
  • Page 36 Replacing the Needle While holding the needle with your left hand, use the screwdriver to tighten the needle clamp screw. Turn the screw toward the back of the machine (clockwise). CAUTION • Be sure to insert the needle until it touches the needle stopper and securely tighten the needle clamp screw with the screwdriver, otherwise the needle may break or damage may result.

  • Page 37: Replacing The Presser Foot

    Replacing the Presser Foot Replacing the Presser Foot Place a different presser foot below the holder so that the presser foot pin is aligned with the notch in the CAUTION holder. • Use the presser foot appropriate for the type of stitch that you wish to sew, otherwise the needle may hit the presser foot, causing the needle to bend or break.

  • Page 38: Removing And Attaching The Presser Foot Holder

    Replacing the Presser Foot ■ Attaching the presser foot holder Note Raise the presser foot lever. • When a stitch is selected, the icon for the presser foot that should be used appears in the screen. Align the presser foot holder with the lower-left side of Check that the correct presser foot is attached before starting to sew.

  • Page 39: Chapter 2 Starting To Sew

    Sewing STARTING TO SEW Chapter Sewing CAUTION • While the machine is in operation, pay special attention to the needle location. In addition, keep your hands away from all moving parts such as the needle and handwheel, otherwise injuries may occur. •...

  • Page 40: Selecting A Stitch Pattern

    Sewing ■ When selecting from the preset utility stitches Character stitches Since various stitches have been assigned to the numeric There are five character stitch modes: Gothic font mode keys, these stitches can be selected simply by pressing the , Handwriting font mode , Outline font mode designated numeric key.

  • Page 41: Sewing A Stitch

    Sewing Lower the presser foot. Sewing a stitch You do not have to pull up the bobbin thread. Adjust the sewing speed with the sewing speed Turn the main power to ON and push (Needle controller. position button) to raise the needle. You can use this controller to adjust sewing speed Select the desired stitch following the procedure during sewing.
  • Page 42 Sewing Insert the foot controller plug into its jack on the machine. CAUTION • Do not press (Thread cutter button) after the threads have been cut. Doing so could tangle the thread or break the needle and damage the machine. •...

  • Page 43: Sewing Reinforcement Stitches

    Sewing Sewing reinforcement stitches Automatic reinforcement stitching Reverse/reinforcement stitches are generally necessary at the After selecting a stitch motif, turn on the automatic reinforcement stitching function before sewing, and the beginning and end of sewing. You can use (Reverse stitch machine will automatically sew reinforcement stitches (or button) to sew reverse/reinforcement stitches (Refer to “Stitch reverse stitches, depending on the stitch motif) at the...
  • Page 44 Sewing Press (Reverse stitch button) or (Reinforcement Reverse stitch Reinforcement stitch button). stitch button button When the automatic Machine starts Machine starts reinforcement sewing and then sewing at the stitching function is sews reinforcement beginning, then not active while stitches while completes the selecting character/ decorative stitches...

  • Page 45: Setting The Stitch

    Setting the Stitch Setting the Stitch This machine is preset with the default settings for the stitch width and stitch length for each stitch. Some models CAUTION are also preset with the default settings for upper thread tension for each stitch. •...

  • Page 46: Setting The Thread Tension

    Setting the Stitch Setting the thread tension You may need to change the thread tension, depending on the fabric and thread being used. ■ Correct thread tension The upper thread and the bobbin thread should cross near the center of the fabric. Only the upper thread should be visible from the right side of the fabric, and only the bobbin thread should be visible from the wrong side of the 1 Wrong side of fabric...

  • Page 47: Saving Stitch Settings

    Setting the Stitch Pushing the thread tension dial toward the right makes the thread tension tighter. Note • The next time that the same straight stitch is selected, the stitch length is set to 2.0 mm. • Both of the stitch width (zigzag width) and stitch length are saved, not just the setting that was changed.

  • Page 48: Useful Functions

    Useful Functions Useful Functions Automatically cutting the thread Memo • Programmed thread-cutting will not be performed The machine can be set to automatically cut the threads at the if the “Start/Stop” button is pressed while sewing. end of the stitching. This is called “programmed thread- Press (Reverse stitch button) or cutting”.

  • Page 49: Adjusting The Presser Foot Pressure

    Useful Functions Select (Automatic fabric sensor system) in the settings screen. Memo • Depending on the selected stitch, mirroring may Set the sensor system to “ON” by pressing the “-” or not be possible; for example, buttonhole stitch. “+” key. •...

  • Page 50: Sewing With Free Motion Mode

    Useful Functions Press the “Start/Stop” button to stop the machine at Note the point where the sewing direction changes. • (Needle position) in the settings screen, must be set to the down position for the pivot function to be used. When (Needle position) is set in the raised position, cannot be used.

  • Page 51: Hands-Free Raising And Lifting Of The Presser Foot

    Useful Functions CAUTION • With free motion quilting, control the feeding speed of the fabric to match the sewing speed. If the fabric is moved faster than the sewing speed, the needle may break or other damage may result. ■ Adjusting free motion presser foot height Select (Free motion foot height) in the settings screen.

  • Page 52: Stitch Setting Chart

    Stitch Setting Chart Stitch Setting Chart Applications, stitch lengths and widths and whether the twin needle can be used are listed for utility stitches in the following table. Patterns printed on the numeric keys on the machine can be selected directly. For details, refer to “Preset utility stitches” on page B-50.
  • Page 53 Stitch Setting Chart Stitch width Stitch length [mm (inch)] [mm (inch)] Reverse/ Presser Twin Reinforce- Walking Stitch Stitch name Applications foot needle ment foot Auto. Auto. stitching Manual Manual Stitch number 2 steps elastic Overcasting (medium 5.0 (3/16) 1.0 (1/16) zigzag stitch weight and stretch 0.0 - 7.0...
  • Page 54 Stitch Setting Chart Stitch width Stitch length [mm (inch)] [mm (inch)] Reverse/ Presser Twin Reinforce- Walking Stitch Stitch name Applications foot needle ment foot Auto. Auto. stitching Manual Manual Stitch number Piecing stitch Piecework/patchwork 1.5 (1/16) 2.0 (1/16) (Left) 6.5 mm (approx. 1/4 0.0 - 7.0 0.2 - 5.0 Reverse...
  • Page 55 Stitch Setting Chart Stitch width Stitch length [mm (inch)] [mm (inch)] Reverse/ Presser Twin Reinforce- Walking Stitch Stitch name Applications foot needle ment foot Auto. Auto. stitching Manual Manual Stitch number Rick-rack Decorative top 4.0 (3/16) 2.5 (3/32) Reinforce- stitch stitching 0.0 - 7.0 0.4 - 5.0...
  • Page 56 Stitch Setting Chart Stitch width Stitch length [mm (inch)] [mm (inch)] Reverse/ Presser Twin Reinforce- Walking Stitch Stitch name Applications foot needle ment foot Auto. Auto. stitching Manual Manual Stitch number Hemstitching Heirloom, decorative 6.0 (15/64) 3.0 (1/8) Reinforce- hems 0.0 - 7.0 0.4 - 5.0 ment...
  • Page 57 Stitch Setting Chart Stitch width Stitch length [mm (inch)] [mm (inch)] Reverse/ Presser Twin Reinforce- Walking Stitch Stitch name Applications foot needle ment foot Auto. Auto. stitching Manual Manual Stitch number Keyhole Buttonholes with buttonhole vertical bar tack for 7.0 (1/4) 0.5 (1/32) Automatic stitch...
  • Page 58 Stitch Setting Chart ■ Preset utility stitches The most frequently used utility stitches have been assigned to the numeric keys. These stitches can be selected simply by pressing the designated key while in the preset utility stitch mode. Stitch name Preset utility stitches Stitch number...

  • Page 59: Sewing

    Sewing This section describes procedures for using the various utility stitches as well as other functions. It provides details on basic sewing in addition to the more expressive features of the machine, such as sewing tubular pieces and buttonholes. Page number starts with “S” in this section. Chapter1 SEWING ATTRACTIVE FINISHES......

  • Page 60: Sewing Tips

    Sewing Tips SEWING ATTRACTIVE Chapter FINISHES Sewing Tips Trial sewing Sewing curves After you have set up the machine with the thread and needle Stop sewing, and then slightly change the sewing direction to appropriate for the type of fabric being sewn, the machine sew around the curve.

  • Page 61: Sewing An Even Seam Allowance

    Sewing Tips ■ Aligning the fabric with a needle plate marking Sewing an even seam allowance The markings on the needle plate show the distance from the needle position of a seam sewn with the straight stitch To sew an even seam, start sewing so that the seam allowance (left needle position).

  • Page 62: Sewing Various Fabrics

    Sewing Various Fabrics Sewing Various Fabrics Release the presser foot locking pin (black button). Sewing thick fabrics → The presser foot remains level, allowing the fabric to be fed. ■ If the fabric does not fit under the presser foot If the fabric does not fit easily under the presser foot, raise the presser foot lever even higher to bring the presser foot to its highest position.

  • Page 63: Sewing Stretch Fabrics

    Sewing Various Fabrics Sewing stretch fabrics Sewing hook-and-loop fastener tape First, baste the pieces of fabric together, and then sew without stretching the fabric. CAUTION • Use only the adhesive-free hook-and-loop fastener tape which is designed for sewing. When the glue adheres to the needle or the bobbin hook race, it may cause malfunction.

  • Page 64: Chapter 2 Utility Stitches

    Basic Stitching UTILITY STITCHES Chapter Basic Stitching Straight stitches are used for sewing plain seams. Basic stitching • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations” section. Baste or pin together the fabric pieces. Attach zigzag foot “J”.
  • Page 65 Basic Stitching ■ Changing the needle position The needle position used as the baseline is different for the straight stitch (left needle position) and the straight stitch (center needle position). 1 Straight stitch (left needle position) 2 Straight stitch (center needle position) When the stitch width of the straight stitch (left needle position) is set to its standard setting (0.0 mm), the distance from the needle position to the right side of the...

  • Page 66: Blind Hem Stitching

    Blind Hem Stitching Blind Hem Stitching Secure the bottoms of skirts and pants with a blind hem. Use a chalk to mark on the fabric about 5 mm (3/16 inch) from the edge of the fabric, and then baste it. •...
  • Page 67 Blind Hem Stitching Slide the item that you wish to sew onto the free arm, make sure that the fabric feeds correctly, and then start Memo sewing. • Blind hem stitches cannot be sewn if the left needle drop point does not catch the fold. If the needle catches too much of the fold, the fabric cannot be unfolded and the seam appearing on the right side of the fabric will be very large,...
  • Page 68 Blind Hem Stitching Example: Normal fabric 1 Wrong side of fabric 2 Right side of fabric Sew with the fold of the hem against the presser foot guide. Press the “Start/Stop” button to stop sewing when you are finished, and raise the presser foot and needle to remove the fabric by pulling it back.

  • Page 69: Overcasting Stitches

    Overcasting Stitches Overcasting Stitches Sew overcasting stitches along the edges of cut fabric to Sew with the edge of the fabric against the presser foot guide. prevent them from fraying. Sewing overcasting stitches using overcasting foot “G” • Using the table below, refer to “Using the utility stitch tables in the “Sewing”...

  • Page 70: Sewing Overcasting Stitches Using Zigzag Foot "J

    Overcasting Stitches Sewing overcasting stitches using zigzag foot “J” • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations” section. 1 Needle drop point Stitch name Stitch Sewing overcasting stitches using the side cutter (sold separately with some models) Stitch number Using the side cutter, seam allowances can be finished...
  • Page 71 Overcasting Stitches Remove the presser foot. Select a stitch. Hook the connecting fork of the side cutter onto the Make a cut of about 2 cm (3/4 inch) long in the fabric needle clamp screw. at the beginning of the stitching. 1 2 cm (3/4 inch) Position the fabric in the side cutter.

  • Page 72: Buttonhole Stitching/Button Sewing

    Buttonhole Stitching/Button Sewing Buttonhole Stitching/Button Sewing • Using the table below, refer to “Using the utility Buttonhole sewing stitch tables in the “Sewing” section” in the “Basic operations” section. The maximum buttonhole length is about 28 mm (1-1/8 inches) (diameter + thickness of the button). Buttonholes are sewn from the front of the presser foot to the back, as shown below.
  • Page 73 Buttonhole Stitching/Button Sewing Use chalk to mark on the fabric the position and length Select a stitch. of the buttonhole. Position the fabric with the front end of the buttonhole mark aligned with the red marks on the sides of the buttonhole foot, and then lower the presser foot lever.
  • Page 74 Buttonhole Stitching/Button Sewing Gently hold the end of the upper thread in your left For keyhole buttonholes, use the eyelet punch to make hand, and then start sewing. a hole in the rounded end of the buttonhole, and then use the seam ripper to cut open the buttonhole. →...

  • Page 75: Button Sewing

    Buttonhole Stitching/Button Sewing Hook the gimp thread onto the part of buttonhole foot Raise the presser foot lever, and then slide the feed dog “A” shown in the illustration. position switch, located at the rear of the machine on the base, to (to the left as seen from the rear of the machine).
  • Page 76 Buttonhole Stitching/Button Sewing ■ Attaching a shank to a button Turn the handwheel toward you (counterclockwise) to check that the needle correctly goes into the two holes To sew the button with a shank, attach the button with of the button. space between it and the fabric, and then wind the thread by hand.

  • Page 77: Zipper Insertion

    Zipper Insertion Zipper Insertion Press open the seam allowance from the wrong side of • Using the table below, refer to “Using the utility the fabric. stitch tables in the “Sewing” section” in the “Basic operations” section. Stitch name Stitch 1 Wrong side of fabric Stitch number Align the seam with the center of the zipper, and then...

  • Page 78: Inserting A Side Zipper

    Zipper Insertion Select stitch Inserting a side zipper Stitching is visible on only one piece of fabric. Use this type of zipper application for side openings and back openings. CAUTION • When using zipper foot “I”, be sure to select the straight stitch (center needle position), and slowly turn the handwheel toward you (counterclockwise) to check that the needle...
  • Page 79 Zipper Insertion Press the seam allowance so that the right side (the side Sew the zipper to the piece of fabric with the extra 3 that will not be stitched) has an extra 3 mm (1/8 inch). mm (1/8 inch), starting from the base of the zipper. 1 Wrong side of fabric 2 3 mm (1/8 inch) Align the zipper teeth with the pressed edge of the...
  • Page 80 Zipper Insertion Topstitch around the zipper. Sew reverse stitches at the end of the zipper opening and align the zipper teeth with the side of the presser foot. 1 Right side of fabric 2 End of zipper opening 3 Reverse stitches 4 Beginning of stitching 5 Basting stitching CAUTION...

  • Page 81: Zipper/Piping Insertion

    Zipper/piping Insertion Zipper/piping Insertion A zipper and piping can be sewn in place. Slide the presser foot over either the left or right feed dog. • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations”...

  • Page 82: Inserting A Piping

    Zipper/piping Insertion Topstitch around the zipper. After sewing, turn them over. 1 Stitching 2 Right side of fabric 3 Basting stitching 4 End of zipper opening CAUTION • When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break.

  • Page 83: Sewing Stretch Fabrics And Elastic Tape

    Sewing Stretch Fabrics and Elastic Tape Sewing Stretch Fabrics and Elastic Tape • Using the table below, refer to “Using the utility Pin the elastic tape to the wrong side of the fabric. stitch tables in the “Sewing” section” in the “Basic Pin the elastic tape to the fabric at a few points to make operations”...

  • Page 84: Appliqué, Patchwork And Quilt Stitching

    Appliqué, Patchwork and Quilt Stitching Appliqué, Patchwork and Quilt Stitching • Using the table below, refer to “Using the utility Appliqué stitching stitch tables in the “Sewing” section” in the “Basic operations” section. Cut out the appliqué, leaving a seam allowance of between 3 and 5 mm (1/8 and 3/16 inch).

  • Page 85: Patchwork (Crazy Quilt) Stitching

    Appliqué, Patchwork and Quilt Stitching Turn the handwheel toward you (counterclockwise), Piecing and then begin sewing around the edge of the appliqué, making sure that the needle drops just outside of the appliqué. Sewing together two pieces of fabric is called “piecing”. The fabric pieces should be cut with a 6.5 mm (1/4 inch) seam allowance.

  • Page 86: Sold Separately With Some Models

    Appliqué, Patchwork and Quilt Stitching ■ Piecing using the 1/4" quilting foot with guide Topstitching quilting, 1/8 inch (sold separately with some models) Sew with the edge of the fabric aligned with the left side of the presser foot end. This quilting foot can sew an accurate 1/4 inch or 1/8 inch seam allowance.

  • Page 87: Quilting

    Appliqué, Patchwork and Quilt Stitching Start sewing. Baste the fabric to be quilted. When the end of the stitching is reached, stop the Remove the presser foot and the presser foot holder. machine. • For details, refer to “Removing and attaching the Sew until the mark at the lower edge of the 1/4"...

  • Page 88: Free Motion Quilting

    Appliqué, Patchwork and Quilt Stitching ■ Using the quilting guide (sold separately with ■ Using free motion open toe quilting foot “O”* some models) or quilting foot* Use the quilting guide to sew parallel stitches that are * Sold separately with some models. equally spaced.
  • Page 89 Appliqué, Patchwork and Quilt Stitching Hold the quilting foot in place with your right hand, and tighten the presser foot holder screw using the CAUTION screwdriver with your left hand. • When using free motion quilting foot “C”, be sure to use the straight stitch needle plate and sew with the needle in middle (center) needle position.
  • Page 90 Appliqué, Patchwork and Quilt Stitching Attach free motion quilting foot “C” at the front with After sewing is finished, slide the feed dog position the presser foot holder screw aligned with the notch in switch lever to (to the right as seen from the rear the quilting foot.
  • Page 91 Appliqué, Patchwork and Quilt Stitching Tighten the screw with the included screwdriver. CAUTION • With free motion quilting, control the feeding speed of the fabric to match the sewing speed. If the fabric is moved faster than the sewing speed, the needle may break or other damage may result.

  • Page 92: Satin Stitching Using The Sewing Speed Controller

    Appliqué, Patchwork and Quilt Stitching Finished project Select stitch While sewing, slide the sewing speed controller to adjust the stitch width. Slide the controller to the left to make the width narrower. Slide the controller to the right to make the width wider.

  • Page 93: Reinforcement Stitching

    Reinforcement Stitching Reinforcement Stitching Reinforce points that will be subject to strain, such as sleeve Bar tack stitching holes, inseams and pocket corners. • Using the table below, refer to “Using the utility Bar tacks are used to reinforce points subject to strain, such as stitch tables in the “Sewing”...

  • Page 94: Darning

    Reinforcement Stitching • When lowering the presser foot, do not push in the Darning front of the presser foot, otherwise the bar tack will not be sewn with the correct size. 1 Do not reduce the gap. Pull down the buttonhole lever as far as possible. 1 Reinforcement stitching Determine the desired length of the darning.
  • Page 95 Reinforcement Stitching Position the fabric so that the needle is 2 mm (1/16 Raise the presser foot lever, remove the fabric, and inch) in front of the area to be darned. then cut the threads. Raise the buttonhole lever to its original position. Memo •...

  • Page 96: Eyelet Stitching

    Eyelet Stitching Eyelet Stitching Eyelets, such as those on belts, can be sewn. Use the eyelet punch to cut a hole in the center of the eyelet. • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic operations”...

  • Page 97: Attaching Patches Or Emblems To Shirt Sleeves

    Attaching Patches or Emblems to Shirt Sleeves Attaching Patches or Emblems to Shirt Sleeves Lower the needle into the fabric at the beginning of the Use these stitch patterns to attach patches or emblems to stitching, and then start sewing. pant legs, shirt sleeves, etc.
  • Page 98 Attaching Patches or Emblems to Shirt Sleeves After you have sewn to the corner, stop the machine, and then select stitch again. After sewing 3 to 5 stitches at the beginning of the stitching, stop the machine. Memo • The feeding direction of the fabric differs depending on the stitch that is selected.

  • Page 99: Decorative Stitching

    Decorative Stitching Decorative Stitching The utility stitches contain the following decorative stitches. • Using the table below, refer to “Using the utility stitch tables in the “Sewing” section” in the “Basic Stitch name Stitch operations” section. Stitch number Serpentine stitch 2-17 Stitch name Stitch...

  • Page 100: Scallop Stitching

    Decorative Stitching Sew with the center of the presser foot aligned along Smocking the center of the two pieces of fabric. The decorative stitch created by stitching or embroidering over gathers is called “smocking”. It is used to decorate the front of blouses or cuffs.

  • Page 101: Shell Tuck Stitching

    Decorative Stitching Sew while making sure that the needle drops slightly Select stitch off the edge of the fabric. Stitch between the straight stitches. 1 Needle drop point Pull out the threads for the straight stitches. Unfold the fabric, and then iron the tucks down to one side.

  • Page 102: Heirloom Stitching

    Decorative Stitching Turn the fabric over so that the right side faces up, and Start sewing. then sew over the seam with the center of the presser foot aligned with the seam. CAUTION 1 Right side of fabric • When sewing with the wing needle, select a Heirloom stitching stitch width of 6.0 mm (15/64 inch) or less, otherwise the needle may bend or break.
  • Page 103 Decorative Stitching With the right side of the fabric facing up, sew along Sew along the center of the unfrayed section. the right edge of the frayed section. Press the mirror image key. • For details, refer to “Mirroring stitches” in the “Basic operations”...
  • Page 104 Decorative Stitching S-46...

  • Page 105: Decorative Sewing

    Decorative sewing This section provides instructions on sewing character stitches and decorative stitches as well as on adjusting and editing them. Page number starts with “D” in this section. The screen display and machine illustration may vary slightly, depending on the machine model. Chapter1 CHARACTER / DECORATIVE STITCHES....

  • Page 106: Chapter 1 Character / Decorative Stitches

    Sewing the Various Built-in Decorative Patterns CHARACTER / Chapter DECORATIVE STITCHES Sewing the Various Built-in Decorative Patterns Cross stitch stitches Selecting stitch patterns This machine is equipped with the following decorative stitches and character stitches. Character stitch patterns Operation Font Icon Gothic Handwriting...

  • Page 107: Deleting A Pattern

    Sewing the Various Built-in Decorative Patterns ■ Character stitch patterns Memo Each press of changes the font in the following order. • If a new pattern is selected without deleting the previously selected one, the first and second patterns are combined. (Refer to “Combining patterns”...

  • Page 108: Basic Sewing

    Sewing the Various Built-in Decorative Patterns Basic sewing Memo • When sewing character stitches, the machine Select a decorative/character stitch pattern. automatically sews reinforcement stitches at the beginning and end of each character. Attach monogramming foot “N”. Place the fabric under the presser foot, pull the upper thread out to the side, press (Needle position button) to lower needle into fabric and then lower the...

  • Page 109: Combining Patterns

    Sewing the Various Built-in Decorative Patterns Combining patterns Repeating combined patterns When multiple stitches are combined, the sewing machine Select the first category and pattern. stops when the pattern displayed on the screen has been completed. Use the following operations to sew a combined →...

  • Page 110: Checking The Selected Pattern

    Sewing the Various Built-in Decorative Patterns Large Checking the selected pattern When the specified pattern is not displayed on the screen, check the pattern using the following steps. Select (Check) in the settings screen. Small Repeat steps Press the “-” or “+” key, and confirm the pattern. Changing the stitch density Press If a satin stitch has been selected, the stitch density can be...

  • Page 111: Changing The Pattern Length

    Sewing the Various Built-in Decorative Patterns Changing the pattern length Creating step stitch patterns (For models equipped with step stitch The length of one part of a 7 mm satin stitch can be set to one of five sizes. patterns) Select a 7 mm satin stitch pattern.

  • Page 112: Mirroring A Pattern Image

    Sewing the Various Built-in Decorative Patterns Press Mirroring a pattern image After a single pattern has been selected, press mirror the pattern image horizontally. → The next pattern selected is moved half a width to the left. Press to specify that the patterns will be sewn repeatedly.

  • Page 113: Returning To The Beginning Of The Pattern

    Sewing the Various Built-in Decorative Patterns Returning to the beginning of the pattern Saving a pattern You can return to the beginning of the pattern after trial Combined patterns can be stored for later use. Since stored sewing or when the stitching is sewn incorrectly. patterns are not lost after the sewing machine is turned off, they can be recalled at any time.

  • Page 114: Retrieving A Pattern

    Sewing the Various Built-in Decorative Patterns Attach monogramming foot “N”. Retrieving a pattern Press once or twice until a list of saved patterns like the one shown below is displayed. Select Start sewing. Select the desired saved pattern using → The sewing machine stops after it has finished sewing the pattern.
  • Page 115 Sewing the Various Built-in Decorative Patterns Press the “-” or “+” key to adjust the vertical position. Press Select once again, start the sewing machine and check the stitching. Continue adjusting the pattern until it is sewn correctly. → Make the necessary adjustments according to how the pattern is sewn.
  • Page 116 Sewing the Various Built-in Decorative Patterns D-12...

  • Page 117: Appendix

    Appendix This section provides important information for operating this machine. Please read this section to find troubleshooting tips and pointers as well as how to keep your machine in the best working order. Page number starts with “A” in this section. Chapter1 MAINTENANCE AND TROUBLESHOOTING ..

  • Page 118: Chapter 1 Maintenance And Troubleshooting

    If problems occur, such as difficulty turning the handwheel or CAUTION an unusual noise, immediately stop using the machine, and contact your authorized Baby Lock retailer. • Unplug the power cord before cleaning the machine, otherwise injuries or an electric shock may occur.
  • Page 119 Care and Maintenance Remove the needle plate cover. • Align the marks. Grasp both sides of the needle plate cover, and then slide it toward you. mark mark 1 Needle plate cover 3 Bobbin case Remove the bobbin case. • Make sure that the indicated points are aligned Grasp the bobbin case, and then pull it out.

  • Page 120: Frequent Troubleshooting Topics

    “ www.babylock.com ”. appropriate tension being applied to the bobbin thread, it If the problem persists, contact your authorized Baby Lock is pulled through the fabric when the upper thread is pulled up. For this reason, the thread is visible from the retailer.

  • Page 121: Tangled Thread On Wrong Side Of Fabric

    Troubleshooting ■ Remedy/check details Pull the thread to pass it through the slit in the needle plate cover, then cut it with the cutter. Remove the tangled thread, and then correct the upper threading. Remove the tangled thread. If it cannot be removed, cut the thread with scissors.

  • Page 122: Incorrect Thread Tension

    Troubleshooting Pass the thread under the thread guide plate, and then Incorrect thread tension pull it up. ■ Symptoms • Symptom 1: The bobbin thread is visible from the right side of the fabric. (Refer to illustration below) • Symptom 2: The upper thread appears as a straight line on the right side of the fabric.

  • Page 123: Fabric Is Caught In The Machine And Cannot Be Removed

    Using thread tension key (For models equipped with it forcefully, contact your nearest authorized Baby Lock thread tension key. Refer to page B-6) Press “-” to decrease the tension of the upper thread.
  • Page 124 Remove the bobbin case. If threads remain in the bobbin case, remove them. If the fabric cannot be removed, even after completing these steps, contact your nearest authorized Baby Lock retailer. Remove any threads in the race and around the feed dogs.
  • Page 125 Troubleshooting Turn the handwheel to check that the feed dogs move Attach the needle plate cover according to step smoothly and do not contact the edges of the slots in the “Cleaning the race” on page A-2. needle plate. Check the condition of the needle, and then install it. If the needle is in a poor condition, for example, if it is bent, be sure to install a new needle.

  • Page 126: When The Thread Became Tangled Under The Bobbin Winder Seat

    If the needle or feed dogs contact the needle plate, the machine may be malfunctioning; therefore, contact your nearest authorized Baby Lock retailer. Turn off the machine, and then install the bobbin and presser foot. • Refer to “Installing the bobbin” and “Replacing the presser foot”...
  • Page 127 Troubleshooting Hold the thread end with your left hand, and wind off the thread clockwise with your right hand as shown below. Wind the bobbin again. Note • Make sure that the thread passes under the pretension disk of the bobbin-winding thread guide correctly.

  • Page 128: List Of Symptoms

    Cannot thread the needle. The needle threader hook is bent and does not Contact your authorized Baby Lock retailer. – pass through the eye of the needle. The needle threader lever cannot be moved or Contact your authorized Baby Lock retailer.
  • Page 129 B-12 the sensitivity is for the user. too strong. The sewing light is damaged. Contact your authorized Baby Lock retailer. – The sewing light (Light) is set to “OFF” in the settings does not come on. Change the setting to “ON”.
  • Page 130 There are scratches around the opening in the Replace the needle plate, or consult your breaks. needle plate. authorized Baby Lock retailer. There are scratches around the opening in the Replace the presser foot, or consult your B-29 presser foot.
  • Page 131 There are needle holes or friction scratches in Replace the bobbin case, or consult your the bobbin case. authorized Baby Lock retailer. Slide the feed dog position switch to the right Feed dogs are set in the down position. Stitches are too close together.
  • Page 132 Probable Cause Remedy Reference The fabric feeds in the opposite The feed mechanism is damaged. Contact your authorized Baby Lock retailer. – direction. Firmly tighten the needle clamp screw. If the The needle The needle clamp screw is loose. needle is bent or blunt, replace it with a new...

  • Page 133: Error Messages

    Troubleshooting ■ After sewing Symptom Probable Cause Remedy Reference Check the steps for threading the machine and Upper threading is incorrect. B-19 rethread the machine. Reset the bobbin. (If needle plate was removed, reinstall needle plate and tighten screws prior to Bobbin is set incorrectly.
  • Page 134 Troubleshooting Error Messages Cause/Solution This message is displayed when (Twin needle) is set to “ON”, and a stitch pattern that cannot be sewn with the twin needle is selected. This message is displayed when the “Start/Stop” button was pressed while the foot controller was connected.
  • Page 135 This message is also displayed when the needle plate is removed while the machine is still turned on. If error message “F**” appears in the LCD while the machine is being used, the machine may be malfunctioning. Contact your nearest authorized Baby Lock retailer. Appendix A-19...

  • Page 136: Operation Beep

    Specifications Operation beep Nothing appears in the LCD Each time a key is pressed you will hear one beep. If an If nothing appears in the LCD when the machine is turned on, incorrect operation is performed you will hear two or four the brightness of the LCD is either too light or too dark.

  • Page 137: Index

    Index Index Numerics Darning stitch ................S-35 Decorative stitches & patterns ............ D-2 1/4" quilting foot ............... S-28 Drawnwork ................S-44 1/4" quilting foot with guide ............. S-28 7 mm satin stitches ..............D-2 Error messages ................. A-17 Even seam allowance ..............S-3 Accessories Eyelet stitching ................
  • Page 138 Index Replacing needle ..............B-27 Replacing presser foot .............. B-29 Needle Reverse stitch button ............B-4 B-35 condition ................B-27 Reverse/Reinforcement stitches ..........B-35 position ................... S-7 replacement ................. B-27 threading ................B-21 types, sizes & uses ..............B-26 Satin stitch length, changing ............D-7 Needle bar thread guide ............
  • Page 139 Index Zigzag stitches ............... S-12 S-26 Zigzag width adjustment ............B-37 Zipper insertion centered ..............S-19 S-23 side ..................S-20 Appendix A-23...
  • Page 140 English 888-F51/F61/F71 Printed in Vietnam XG0017-101...

This manual is also suitable for:

Lyric blmlrKatherine bl210a

Table of Contents