CONFIDENTIAL 1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the (READING SHOULD circuit board. NOT BE ABOVE 0.5mA) Disconnect the AC power and DC Power Jack before servicing.
CONFIDENTIAL 1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
CONFIDENTIAL 2 Product Specifications 2-2 Pin Assignments 2-2-1 15Pin D-Sub Separate Composite Sync-on-green Pin No. Green Green Green + H/V Sync. Blue Blue Blue GND (DDC Return) GND (DDC Return) GND (DDC Return) GND-Red GND-Red GND-Red GND-Green GND-Green GND-Green GND-Blue GND-Blue GND-Blue No Connection...
Page 7
CONFIDENTIAL 2 Product Specifications 2-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. 2-3-1 LCD Panel Mode : 1 mode Definition of Terms "Active"Video Blanking Video Back Top/Left "Addressable"Video...
CONFIDENTIAL 3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the MO17W* monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 Disassembly Cautions:1. Disconnect the monitor from the power source before disassembly. 2.
Page 12
CONFIDENTIAL 3 Disassembly and Reassembly 4. Remove 2 flat head screws from the hinge mounting. Do not remove the screw for cable clamp. 5. Disconnect the stand cable from socket and remove stand assembly. 6. Remove 2 screws on cover rear. 7.
Page 13
CONFIDENTIAL 3 Disassembly and Reassembly 9. Disconnect the function cable from the connector on PCB. 10. Open the cover shield. MO17W*...
Page 14
CONFIDENTIAL 3 Disassembly and Reassembly 3-2 Replacement Order of Lamp Assemblies 1. After confirm there is nothing on the desk turn the LCD module over and put it on a flat desk. 2. Push down the stopper and slide the lamp unit out. 3.
Page 15
CONFIDENTIAL 3 Disassembly and Reassembly 4. Attach the new lamp units on the LCD module : opposite process 2 and 3 Replacement of lamp unit should be done at the power off state on a clean work bench. 3-3 Reassembly Reassembly procedures are in the reverse order of disassembly procedures.
Page 16
CONFIDENTIAL 3 Disassembly and Reassembly Memo MO17W*...
CONFIDENTIAL 4 Troubleshooting Notes: 1. Before troubleshooting, setup the PC’s display as below. • Resolution: 1280 x 768 • H-frequency: 48 KHz • V-frequency: 60 Hz 2. If no picture appears, make sure the power cord is correctly connected. 3. Check the following circuits. •...
Page 18
CONFIDENTIAL 4 Troubleshooting 4-2-1 No Video [Analog] Check signal cable and connection. Does the video signal appear at Pin 48, 47, 46, 45, 42, 41, 40, 39, 38, and 37 of IC401? Is Pin 2(BKLT_EN) of IC203 High? Check TFT-LCD panel and Inverter. Check IC301 and related circuit.
CONFIDENTIAL 4 Troubleshooting 4-2-2 No Video [Digital] Check signal cable and connection. Does the video signal appear at Pin 48, 47, 46, 45, 42, 41, 40, 39, 38, and 37of IC401? Is Pin 2(BKLT_EN) of IC203 High? Check TFT-LCD panel and Inverter. Check IC301 and related circuit.
CONFIDENTIAL 8 Wiring Diagram CN401 INVERTER CN102 BRT_ADJ BRIGHT BL_ON/OFF BKLT_EN MAIN PCB +14V DC +14V DC +14V DC +14V DC +14V DC +14V DC CN201 CN601 MO17W*...